- 您現在的位置：買賣IC網 > PDF目錄358868 > LM5021NA-2 (NATIONAL SEMICONDUCTOR CORP) AC-DC Current Mode PWM Controller PDF資料下載
參數資料
| 型號： | LM5021NA-2 |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | AC-DC Current Mode PWM Controller |
| 中文描述： | 0.7 A SWITCHING CONTROLLER, 560 kHz SWITCHING FREQ-MAX, PDIP8 |
| 封裝： | PLASTIC, DIP-8 |
| 文件頁數： | 9/15頁 |
| 文件大?。?/td> | 746K |
| 代理商： | LM5021NA-2 |
Detailed Operating Description
(Continued)
frequency and the operational output frequency are the
same. To set a desired output switching frequency (Fsw), the
RT resistor can be calculated from:
LM5021-1:
LM5021-2:
The LM5021 can also be synchronized to an external clock.
The external clock must have a higher frequency than the
free running oscillator frequency set by the RT resistor. The
clock signal should be capacitively coupled into the RT pin
with a 100pF capacitor. A peak voltage level greater than 3.8
Volts at the RT pin is required for detection of the sync pulse.
The dc voltage across the RT resistor is internally regulated
at 2 volts. Therefore, the ac pulse superimposed on the RT
resistor must have 1.8V or greater amplitude to successfully
synchronize the oscillator. The sync pulse width should be
set between 15ns to 150ns by the external components. The
RT resistor is always required, whether the oscillator is free
running or externally synchronized. The RT resistor should
be located very close to the device and connected directly to
the pins of the LM5021 (RT and GND).
GATE DRIVER and MAX DUTY CYCLE LIMIT
The LM5021 provides a gate driver (OUT), which can source
peak current of 0.3A and sink 0.7A. The LM5021 is available
in two duty-cycle limit options. The maximum output duty-
cycle is typically 80% for the LM5021-1 option, and precisely
equal to 50% for the LM5021-2 option. The maximum duty
cycle function for the LM5021-2 is accomplished with an
internal toggle flip-flop to ensure an accurate duty cycle limit.
The internal oscillator frequency of the LM5021-2 is there-
fore twice the switching frequency of the PWM controller
(OUT pin).
The 80% maximum duty-cycle function for the LM5021-1 is
determined by the internal oscillator. For the LM5021-1 the
internal oscillator frequency and the switching frequency of
the PWM controller are the same.
SOFT-START
The soft-start feature allows the power converter to gradually
reach the initial steady state operating point, thus reducing
start-up stresses and current surges. An internal 22 μA
current source charges an external capacitor connected to
the SS pin. The capacitor voltage will ramp up slowly, limiting
the COMP pin voltage and the duty cycle of the output
pulses. The soft-start capacitor is also used to generate the
hiccup mode delay time when the output of the switching
power supply is continuously overloaded.
HICCUP MODE OVERLOAD CURRENT LIMITING
Hiccup mode is a method of protecting the power supply
from over-heating and damage during an extended overload
condition. When the output fault is removed the power sup-
ply will automatically restart.
Figure 3
,
Figure 4
and
Figure 5
illustrate the equivalent
circuit of the hiccup mode for LM5021 and the relevant
waveforms. During start-up and in normal operation, the
external soft-start capacitor Css is pulled up by a current
source that delivers 22 μA to the SS pin capacitor. In normal
operation, the soft-start capacitor continues to charge and
eventually reaches the saturation voltage of the current
source (V
SS_OCV
, nominally 5.2V). During start-up the
COMP pin voltage follows the SS capacitor voltage and
gradually increases the peak current delivered by the power
supply. When the output of the switching power supply
reaches the desired voltage, the voltage feedback amplifier
takes control of the COMP signal (via the opto-coupler). In
normal operation the COMP level is held at an intermediate
voltage between 1.25V and 2.75V controlled by the voltage
regulation loop. When the COMP pin voltage is below 1.25V,
the duty-cycle is zero. When the COMP level is above 2.75V,
the duty cycle will be limited by the 0.5V threshold of cycle-
by-cycle current limit comparator.
If the output of the power supply is overloaded, the voltage
regulation loop demands more current by increasing the
COMP pin control voltage. When the COMP pin exceeds the
over voltage detection threshold (V
, nominally 4.6V),
the SS capacitor Css will be discharged by a 10 μA overload
detection timer current source, I
. If COMP remains
above V
long enough for the SS capacitor to discharge
to the Hiccup mode threshold (V
, nominally 4.6V), the
controller enters the hiccup mode. The OUT pin is then
latched low and the SS capacitor discharge current source is
reduced from 10 μA to 0.25 μA, the dead-time current
source, I
. The SS pin voltage is slowly reduced until it
reaches the Restart threshold (V
, nominally 0.3V). Then
a new start-up sequence commences with 22 μA current
source charging the capacitor C
SS
. The slow discharge of
the SS capacitor from the Hiccup threshold to the Restart
threshold provides an extended off time that reduces the
overheating of components including diodes and MOSFETs
due to the continuous overload. The off time during the
hiccup mode can be calculated from the following equation:
Example:
Toff = 808 ms, assuming the C
SS
capacitor value is 0.047 μF
Short duration intermittent overloads will not trigger the hic-
cup mode. The overload duration required to trigger the
hiccup response is set by the capacitor C
, the 10 μA
discharge current source and voltage difference between the
saturation level of the SS pin and the Hiccup mode thresh-
old.
Figure 5
shows the waveform of SS pin with a short
duration overload condition. The overload time required to
enter the hiccup mode can be calculated from the following
equation:
Example:
Toverload = 2.82 ms, assuming the C
SS
capacitor value is
0.047 μF
L
www.national.com
9
相關PDF資料 |
PDF描述 |
|---|---|
| LM5021MMX-1 | AC-DC Current Mode PWM Controller |
| LM5021MMX-2 | AC-DC Current Mode PWM Controller |
| LM5021 | AC-DC Current Mode PWM Controller |
| LM5025A | Active Clamp Voltage Mode PWM Controller |
| LM5025AMTC | Active Clamp Voltage Mode PWM Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM5021NA-2/NOPB | 功能描述:IC CONTROLLER PWM AC-DC 8DIP RoHS:是 類別:集成電路 (IC) >> PMIC - AC-DC 轉換器，離線開關 系列:- 標準包裝:1 系列:FPS™ 輸出隔離:隔離 頻率范圍:61kHz ~ 73kHz 輸入電壓:8 V ~ 26 V 輸出電壓:650V 功率（瓦特）:12W 工作溫度:-40°C ~ 115°C 封裝/外殼:8-DIP（0.300"，7.62mm） 供應商設備封裝:8-MDIP 包裝:Digi-Reel® 其它名稱:FSL206MRBNFSDKR |
| LM5022 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:60V Low Side Controller for Boost and SEPIC |
| LM5022_09 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:60V Low Side Controller for Boost and SEPIC |
| LM5022BSTBLDT/NOPB | 制造商:Texas Instruments 功能描述:60V LOW SIDE CONTROLLER FOR BOOST AND S - Boxed Product (Development Kits) 制造商:Texas Instruments 功能描述:IC REG CTRLR BST PWM |
| LM5022EVAL | 功能描述:BOARD EVALUATION LM5022 RoHS:否 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓撲結構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
發布緊急采購，3分鐘左右您將得到回復。