- 您現在的位置：買賣IC網 > PDF目錄358868 > LM5010SD (NATIONAL SEMICONDUCTOR CORP) RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS PDF資料下載
參數資料
| 型號： | LM5010SD |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| 中文描述： | 1.5 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, DSO10 |
| 封裝： | 4 X 4 MM, LLP-10 |
| 文件頁數： | 12/19頁 |
| 文件大?。?/td> | 453K |
| 代理商： | LM5010SD |
Current Limit
Current limit detection occurs during the off-time by monitor-
ing the recirculating current through the free-wheeling diode
(D1). The detection threshold is 1.25A,
±
0.25A. Referring to
Figure 1
, when the buck switch is off the inductor current
flows through the load, into S
GND
, through the sense resistor,
out of I
SEN
and through D1. If that current exceeds the
threshold the current limit comparator output switches to
delay the start of the next on-time period. The next on-time
starts when the current out of I
SEN
is below the threshold and
the voltage at FB is below 2.5V. If the overload condition
persists causing the inductor current to exceed the threshold
during each on-time, that is detected at the beginning of
each off-time. The operating frequency is lower due to
longer-than-normal off-times.
Figure 12
illustrates the inductor current waveform. During
normal operation the load current is I
, the average of the
ripple waveform. When the load resistance decreases the
current ratchets up until the lower peak attempts to exceed
the threshold. During the Current Limited portion of
Figure
12
, the current ramps down to the threshold during each
off-time, initiating the next on-time (assuming the voltage at
FB is
<
2.5V). During each on-time the current ramps up an
amount equal to:
(6)
During this time the LM5010 is in a constant current mode,
with an average load current (I
OCL
) equal to the threshold +
I/2.
The “valley current limit” technique allows the load current to
exceed the current limit threshold as long as the lower peak
of the inductor current is less than the threshold.
The current limit threshold can be increased by connecting
an external resistor (R
) between S
GND
and I
SEN
. The
external resistor typically is less than 1
is explained in the Applications Information section.
The peak current out of SW and I
must not exceed 3.5A.
The average current out of SW must be less than 3A, and
the average current out of I
SEN
must be less than 2A.
N - Channel Buck Switch and
Driver
The LM5010 integrates an N-Channel buck switch and as-
sociated floating high voltage gate driver. The peak current
through the buck switch must not be allowed to exceed 3.5A,
and the average current must be less than 3A. The gate
driver circuit is powered by the external bootstrap capacitor
between BST and SW (C4). During each off-time, the SW pin
is at approximately -1V, and C4 is re-charged from V
CC
through the internal high voltage diode. The minimum off-
time of 265 ns ensures a minimum time each cycle to
recharge the bootstrap capacitor. A 0.022 μF ceramic ca-
pacitor is recommended for C4.
Softstart
The softstart feature allows the converter to gradually reach
a steady state operating point, thereby reducing startup
stresses and current surges. Upon turn-on, after V
reaches the under-voltage threshold (t1 in
Figure 8
), an
internal 11.5 μA current source charges the external capaci-
tor at the Softstart pin to 2.5V (t2 in
Figure 8
). The ramping
voltage at SS (and at the non-inverting input of the regulation
comparator) ramps up the output voltage in a controlled
manner. This feature keeps the load current from going to
current limit during startup, thereby reducing inrush currents.
An internal switch grounds the Softstart pin if V
CC
is below
the under-voltage lockout threshold, if a thermal shutdown
occurs, or if the circuit is shutdown using the R
ON
/SD pin.
Thermal Shutdown
The LM5010 should be operated so the junction temperature
does not exceed 125C. If the junction temperature in-
creases above that, an internal Thermal Shutdown circuit
activates (typically) at 175C, taking the controller to a low
power reset state by disabling the buck switch and the
on-timer, and grounding the Softstart pin. This feature helps
prevent catastrophic failures from accidental device over-
20119920
FIGURE 12. Inductor Current - Current Limit Operation
L
www.national.com
12
相關PDF資料 |
PDF描述 |
|---|---|
| LM5010SDX | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| LM5010 | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| LM501 | RED OVAL LAMP LED |
| LM5020 | 100V Current Mode PWM Controller |
| LM5020MM-1 | 100V Current Mode PWM Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM5010SD/MEY8 | 制造商:Texas Instruments 功能描述: |
| LM5010SD/NOPB | 功能描述:直流/直流開關轉換器 HIGH VOLTAGE 1A STEP DOWN SWITCHING REG RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| LM5010SDX | 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| LM5010SDX/NOPB | 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| LM5015 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:High Voltage Monolithic Two-Switch Forward DC-DC Regulator |
發布緊急采購，3分鐘左右您將得到回復。