- 您現在的位置：買賣IC網 > PDF目錄30756 > LM4995SDX/NOPB (NATIONAL SEMICONDUCTOR CORP) 1.25 W, 1 CHANNEL, AUDIO AMPLIFIER, DSO8 PDF資料下載
參數資料
| 型號： | LM4995SDX/NOPB |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 1.25 W, 1 CHANNEL, AUDIO AMPLIFIER, DSO8 |
| 封裝： | 3 X 3 MM, 0.5 PICTH, ROHS COMPLIANT, LLP-8 |
| 文件頁數： | 11/16頁 |
| 文件大?。?/td> | 808K |
| 代理商： | LM4995SDX/NOPB |
Electrical Characteristics V
DD = 3.0V
(Notes 1, 2)
The following specifications apply for the circuit shown in Figure 1, unless otherwise specified. Limits apply for T
A = 25C.
Symbol
Parameter
Conditions
LM4995
Units
(Limits)
Typical
Limit
(Notes 7, 8)
I
DD
Quiescent Power Supply Current
V
IN = 0V, Io = 0A, No Load
1.3
mA
V
IN = 0V, Io = 0A, 8
Load
1.6
mA
I
SD
Shutdown Current
V
SD =VGND
0.01
A
V
OS
Output Offset Voltage
No Load
5
mV
P
o
Output Power
THD+N = 1% (max);f=1kHz
400
mW
T
WU
Wake-up time
110
ms
THD+N
Total Harmonic Distortion + Noise
P
o = 250mWRMS; f = 1kHz
0.07
%
PSRR
Power Supply Rejection Ratio
V
ripple = 200mV sine p-p
Input terminated to GND
74 (f = 217Hz)
75 (f = 1kHz)
dB
V
SDIH
Shutdown Voltage Input High
1.2
V
SDIL
Shutdown Voltage Input Low
1
V
Note 1: All voltages are measured with respect to the ground pin, unless otherwise specified.
Note 2: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
functional, but do not guarantee specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which
guarantee specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not guaranteed for parameters where no limit
is given, however, the typical value is a good indication of device performance.
Note 3: The maximum power dissipation must be derated at elevated temperatures and is dictated by TJMAX, θJA, and the ambient temperature TA. The maximum
allowable power dissipation is PDMAX =(TJMAX–TA)/θJA or the number given in Absolute Maximum Ratings, whichever is lower. For the LM4995, see power derating
curves for additional information.
Note 4: Human body model, 100pF discharged through a 1.5k
resistor.
Note 5: Machine Model, 220pF–240pF discharged through all pins.
Note 6: Typicals are measured at 25C and represent the parametric norm.
Note 7: Limits are guaranteed to National’s AOQL (Average Outgoing Quality Level).
Note 8: Datasheet min/max specification limits are guaranteed by design, test, or statistical analysis.
Note 9: ROUT is measured from the output pin to ground. This value represents the parallel combination of the 10k output resistors and the two 20k resistors.
Note 10: If the product is in Shutdown mode and VDD exceeds 6V (to a max of 8V VDD), then most of the excess current will flow through the ESD protection circuits.
If the source impedance limits the current to a max of 10mA, then the device will be protected. If the device is enabled when VDD is greater than 5.5V and less than
6.5V, no damage will occur, although operation life will be reduced. Operation above 6.5V with no current limit will result in permanent damage.
Note 11: Maximum power dissipation in the device (PDMAX) occurs at an output power level significantly below full output power. PDMAX can be calculated using
Equation 1 shown in the Application Information section. It may also be obtained from the power dissipation graphs.
External Components Description
Components
Functional Description
1.
R
i
Inverting input resistance which sets the closed-loop gain in conjunction with R
f. This resistor also forms a
high pass filter with C
i at fC= 1/(2
π R
iCi).
2.
C
i
Input coupling capacitor which blocks the DC voltage at the amplifiers input terminals. Also creates a
highpass filter with R
i at fC = 1/(2
π R
iCi). Refer to the section, Proper Selection of External Components,
for an explanation of how to determine the value of C
i.
3.
R
f
Feedback resistance which sets the closed-loop gain in conjunction with R
i.
4.
C
S
Supply bypass capacitor which provides power supply filtering. Refer to the Power Supply Bypassing
section for information concerning proper placement and selection of the supply bypass capacitor.
5.
C
B
Bypass pin capacitor which provides half-supply filtering. Refer to the section, Proper Selection of External
Components, for information concerning proper placement and selection of C
B.
LM4995
www.national.com
4
相關PDF資料 |
PDF描述 |
|---|---|
| LM5007MMEP/NOPB | SWITCHING REGULATOR, PDSO8 |
| LM5007MMEP | SWITCHING REGULATOR, PDSO8 |
| LM5060MMX | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
| LM5060MM | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
| LM556J/883C | DUAL RECTANGULAR, TIMER, CDIP14 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM4995TM/NOPB | 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| LM4995TMBD | 功能描述:音頻 IC 開發工具 LM4995 DEMO BOARD RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| LM4995TMX/NOPB | 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| LM4A-3M4 | 制造商:BACO Controls Inc 功能描述: |
| LM-4C-30F2-S | 功能描述:基本/快動開關 Foot Switch RoHS:否 制造商:Omron Electronics 觸點形式:SPDT 執行器:Lever 電流額定值:5 A 電壓額定值 AC:250 V 電壓額定值 DC:30 V 功率額定值: 工作力:120 g IP 等級:IP 67 NEMA 額定值: 端接類型:Wire 安裝:Panel |
發布緊急采購，3分鐘左右您將得到回復。