- 您現在的位置：買賣IC網 > PDF目錄385487 > LM4936 (National Semiconductor Corporation) Stereo 2W Audio Power Amplifiers with Volume Control and Selectable Control Interface (SPI or I2C) PDF資料下載
參數資料
| 型號： | LM4936 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | Stereo 2W Audio Power Amplifiers with Volume Control and Selectable Control Interface (SPI or I2C) |
| 中文描述： | 2W的立體聲音頻功率放大器，帶有音量控制和可選控制接口（SPI或I2C） |
| 文件頁數： | 21/28頁 |
| 文件大?。?/td> | 1490K |
| 代理商： | LM4936 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
Application Information
(Continued)
voltage applied to the HP SENSE pin at approximately
50mV. This 50mV puts the LM4936 into bridged mode op-
eration. The output coupling capacitor blocks the amplifier’s
half supply DC voltage, protecting the headphones.
The HP SENSE threshold is set so the output signal cannot
cause an output mode change. While the LM4936 operates
in bridge mode, the DC potential across the load is essen-
tially 0V. Connecting headphones to the headphone jack
disconnects the headphone jack contact pin from R2 and
allows R1 to pull the HP SENSE pin up to V
through R4.
This enables the headphone function and mutes the bridged
speaker. The single-ended ’-’ outputs then drive the head-
phones, whose impedance is in parallel with resistors R2
and R3. These resistors have negligible effect on the
LM4936’s output drive capability since the typical impedance
of headphones is 32
.
Figure 3 also shows the suggested headphone jack electri-
cal connections. The jack is designed to mate with a three-
wire plug. The plug’s tip and ring should each carry one of
the two stereo output signals, whereas the sleeve should
carry the ground return. A headphone jack with one control
pin contact is sufficient to drive the HP-IN pin when connect-
ing headphones.
GAIN SELECT FUNCTION (Bass Boost)
The LM4936 features selectable gain, using either internal or
external feedback resistors. The GAIN SEL bit (B3) controls
which gain is selected. Loading a digital 0 into the GAIN SEL
bit sets the gain to internal resulting in a gain of 6dB for BTL
mode or unity for singled-ended mode. Loading a digital 1
into the GAIN SEL bit sets the gain to be determined by the
external resistors, R
I
and R
F
.
In some cases a designer may want to improve the low
frequency response of the bridged amplifier or incorporate a
bass boost feature. This bass boost can be useful in systems
where speakers are housed in small enclosures. A resistor,
R
, and a capacitor, C
, in parallel, can be placed in series
with the feedback resistor of the bridged amplifier as seen in
Figure 2.
At low, frequencies C
BS
is a virtual open circuit and at high
frequencies, its nearly zero ohm impedance shorts R
BS
. The
result is increased bridge-amplifier gain at low frequencies.
The combination of R
BS
and C
BS
form a -6dB corner fre-
quency at
f
C
= 1/(2
π
R
BS
C
BS
)
(9)
The bridged-amplifier low frequency differential gain is:
A
VD
= 2(R
F
+ R
BS
) / R
i
(10)
Using the component values shown in Figure 2 (R
= 20k
,
R
= 20k
, and C
= 0.068μF), a first-order, -6dB pole is
created at 120Hz. Assuming R
= 20k
, the low frequency
differential gain is 4V/V or 12dB. The input (C
) and output
(C
) capacitor values must be selected for a low fre-
quency response that covers the range of frequencies af-
fected by the desired bass-boost operation.
VOLUME CONTROL
The LM4936 has an internal stereo volume control whose
setting is a function of the digital values in the V4 – V0 bits.
See Table 4.
The LM4936 volume control consists of 31 steps that are
individually selected. The range of the steps, are from 0dB -
78dB. The gain levels are 1dB/step from 0dB to -6dB, 2dB/
step from -6dB to -36dB, 3dB/step from -36dB to -47dB,
4dB/step from -47dB to -51dB, 5dB/step from -51dB to
-66dB, and 12dB to the last step at -78dB.
L
www.national.com
21
相關PDF資料 |
PDF描述 |
|---|---|
| LM4951 | Wide Voltage Range 1.8 Watt Audio Amplifier |
| LM4953 | Ground-Referenced, Ultra Low Noise, Ceramic Speaker Driver |
| LM4953SD | Ground-Referenced, Ultra Low Noise, Ceramic Speaker Driver |
| LM4980 | 2 Cell Battery, 1mA, 42mW Per Channel High Fidelity Stereo Headphone Audio Amplifier for MP3 players |
| LM4980SD | 2 Cell Battery, 1mA, 42mW Per Channel High Fidelity Stereo Headphone Audio Amplifier for MP3 players |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM49360 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Mono Class D Audio Codec PMU with Ground Referenced Headphone Amplifiers, Earpiece Driver, Audio DSP, 2 Step-Down DC-DC Converters, and 7 LDO Regulators |
| LM49360RL | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Mono Class D Audio Codec PMU with Ground Referenced Headphone Amplifiers, Earpiece Driver, Audio DSP, 2 Step-Down DC-DC Converters, and 7 LDO Regulators |
| LM49360RLX | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Mono Class D Audio Codec PMU with Ground Referenced Headphone Amplifiers, Earpiece Driver, Audio DSP, 2 Step-Down DC-DC Converters, and 7 LDO Regulators |
| LM4936MH | 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| LM4936MH/NOPB | 功能描述:音頻放大器 Stereo 2W Audio Pwr Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。