- 您現在的位置：買賣IC網 > PDF目錄385487 > LM4930 (National Semiconductor Corporation) Audio Subsystem with Stereo Headphone & Mono Speaker Amplifiers PDF資料下載
參數資料
| 型號： | LM4930 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | Audio Subsystem with Stereo Headphone & Mono Speaker Amplifiers |
| 中文描述： | 音頻子系統的立體聲耳機 |
| 文件頁數： | 31/33頁 |
| 文件大?。?/td> | 966K |
| 代理商： | LM4930 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁
Application Information
(Continued)
for the bus. It operates at a fixed frequency of 8kHz and may
be set in the BASICCONFIG register (bit 5 PCM_LONG) for
short or long frame sync. A short frame sync is 1 PCM_CLK
cycle (PCM_LONG=0), a long frame sync is 2 PCM_CLK
cycles long (PCM_LONG=1). A long sync pulse is also de-
layed one clock cycle relative to a short sync pulse. This is
illustrated in Figure 3. PCM_CLK is the bit clock for the bus.
It’s frequency depends on the number of 16-bit frames per
sync pulse and can be 128kHz, 256kHz, 512kHz.
The other two lines, PCM_SDO and PCM_SDI, are for serial
data out and serial data in, respectively. The type of data
may also be set in the BASICCONFIG register by bits 6 and
7. Bit 6 controls whether the data is linear or companded. If
set to 1, the 8 MSBs are presumed to be companded data
and the 8 LSBs are ignored. If cleared to 0, the data is
treated as 2’s complement PCM data. Bit 7 controls which
PCM law is used if Bit 6 is set for companded (G711) data. If
set to 1, the companded data is assumed to be A-law. If
cleared to 0, the companded data is treated as μ-law.
Bits 8:9 of the BASICCONFIG register set the PCM_SYNC-
_MODE settings. This controls the number of 16 bit frames
per sync pulse. The feature allows the LM4930 to function
harmoniously with other devices or channels on the PCM
bus by adjusting the number of 16 bit frames per sync pulse
to 1 (00b), 2 (01b), or 4 (10b). The LM4930 will transmit PCM
data in the first frame and then tri-state the PCM_SDO pin on
later frames.
In addition, the LM4930 provides control to allow the PCM-
_CLK and PCM_SYNC clocks to continue functioning even
when the LM4930 is in Standby mode. By setting bit 10 of
the BASICCONFIG register to 1 PCM_ALWAYS_ON is en-
abled and the LM4930 will continue to drive the PCM clock
and sync lines when in Standby mode. This bit should be set
if another codec is using the PCM bus. Powerdown mode
will disable these outputs.
I2S Interface Bus (J2)
The I2S standard provides a uni-directional serial interface
designed specifically for digital audio. For the LM4930, the
interface provides access to a 48kHz, 16 bit full-range stereo
audio DAC. This interface uses a three port system of clock
(I2S_CLK), data (I2S_DATA), and word (I2S_WS). The clock
and word lines can be either master or slave as set by bit 11
in the BASICCONFIG register.
Abit clock (I2S_CLK) at 32 or 64 times the sample frequency
is established by the I2S system master and a word select
(I2S_WS) line is driven at a frequency equal to the sampling
rate of the audio data, in this case 48kHz. The word line is
registered to change on the negative edge of the bit clock.
The serial data (I2S_DATA) is sent MSB first, again regis-
tered on the negative edge of the bit clock, delayed by 1 bit
clock cycle relative to the changing of the word line (typical
I2S format - see Figure 4).
The resolution of the I2S interface may be set by modifying
the I2S_RES bit (bit 12) in the BASICCONFIG register. If set
to 1, the LM4930 operates at 32 bits per frame (3.072MHz).
If cleared to 0, then 16 bits per frame is selected
(1.536MHz). This has a corresponding effect on the bit clock.
The I2S Interface Bus also provides for an additional MCLK
connection to an external device from the LM4930 demo
board. This may be used in conjunction with National Semi-
conductors SPDIF-
>
I2S Conversion Board for quick evalu-
ation. This board features a connection header that inter-
faces with pins 1-5 of the I2S Interface Bus. Pins 6-10 are
provided as digital ground references for the case of discrete
connections.
MCLK/XTAL_IN (P5)
This is the input for an external Master Clock. The jumper at
S2 must be removed (disconnecting the onboard crystal
from the circuit) when using an external Master Clock.
BTL Mono Out (J7)
This is the mono speaker output, designed for use with an 8
ohm speaker. The outputs are driven in bridge-tied-load
(BTL) mode, so both sides have signal. Outputs are normally
biased at one halfAVDD when the LM4930 is in active mode.
Additionally, if the CLASS bit is set to 1 in the VOICETEST-
CONFIG register (bit 0) the BTL mono output is internally
configured as a buffer amplifier designed for use with an
external class D amp.
Stereo Headphone Out (J8)
This is the stereo headphone output. Each channel is single-
ended, with 220uF DC blocking capacitors mounted on the
demo board. The jack features a typical stereo headphone
pinout.
A headphone sense pin is provided at J6. This pin provides
a clean logic high or low output to indicate the presence of
headphones in the headphone jack. A common application
circuit for this is given in the Reference Board Schematic
shown in Figure 5. In this application HPSENSE_IN is pulled
low by the 1k ohm resistor when no headphone is present.
This gives a corresponding logic low output on the
HPSENSE_OUT pin. When a headphone is placed in the
jack the 1k ohm pull-down is disconnected and a 100k ohm
pull-up resistor creates a high voltage condition on
HPSENSE_IN. This in turn creates a logic high on
HPSENSE_OUT. This output may be used to reliably drive
an external microcontroller with headphone status.
MIC Jack (J3)
This jack is for connection to an external microphone like the
kind typically found in mobile phones. Pin 1 is GND, pin 2 is
the negative input pin, and pin 3 is the positive pin, with
phantom voltage supplied by MIC_BIAS on the LM4930.
IRQ (J4)
This pin provides simple status updates from the LM4930 to
an external microcontroller if desired. IRQ is logic high when
the LM4930 is in a stable state and changes to low when
changing modes. This can also be useful for simple
software/driver development to monitor mode changes, or as
a simple debugging tool.
BASIC OPERATION
The LM4930 is a highly integrated audio subsystem with
many different operating modes available. These modes
may be controlled in the BASICCONFIG register in bits 3:0.
These mode settings are shown in the BASICCONFIG reg-
ister table and are described here below:
Powerdown Mode (0000b)
Part is powered down, analog outputs are not biased. This is
a minimum current mode. All part features are shut down.
L
www.national.com
31
相關PDF資料 |
PDF描述 |
|---|---|
| LM4935 | Audio Sub-System with Dual-Mode Stereo Headphone and Mono High Efficiency Loudspeaker Amplifiers and Multi-Purpose ADC |
| LM4935WL | Audio Sub-System with Dual-Mode Stereo Headphone and Mono High Efficiency Loudspeaker Amplifiers and Multi-Purpose ADC |
| LM4935WLX | Audio Sub-System with Dual-Mode Stereo Headphone and Mono High Efficiency Loudspeaker Amplifiers and Multi-Purpose ADC |
| LM4936 | Stereo 2W Audio Power Amplifiers with Volume Control and Selectable Control Interface (SPI or I2C) |
| LM4951 | Wide Voltage Range 1.8 Watt Audio Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM4930_04 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Audio Subsystem with Stereo Headphone & Mono Speaker Amplifiers |
| LM4930ITL | 制造商:Texas Instruments 功能描述:Audio Amp Headphone/Microphone/Speaker 1-CH Mono/2-CH Stereo 1W Class-AB 36-Pin uSMD T/R |
| LM4930ITL/NOPB | 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| LM4930ITLX | 制造商:Texas Instruments 功能描述:Audio Amp Headphone/Microphone/Speaker 1-CH Mono/2-CH Stereo 1W Class-AB 36-Pin uSMD T/R |
| LM4930ITLX/NOPB | 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。