- 您現在的位置：買賣IC網 > PDF目錄30755 > LM4893ITLX/NOPB (NATIONAL SEMICONDUCTOR CORP) 1.1 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA9 PDF資料下載
參數資料
| 型號： | LM4893ITLX/NOPB |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 1.1 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA9 |
| 封裝： | MICRO, BUMP, SMD-9 |
| 文件頁數： | 5/22頁 |
| 文件大?。?/td> | 687K |
| 代理商： | LM4893ITLX/NOPB |
Application Information (Continued)
Selection Of Input Capacitor Size
Large input capacitors are both expensive and space hungry
for portable designs. Clearly, a certain sized capacitor is
needed to couple in low frequencies without severe attenu-
ation. But in many cases the speakers used in portable
systems, whether internal or external, have little ability to
reproduce signals below 100 Hz to 150 Hz. Thus, using a
large input capacitor may not increase actual system perfor-
mance.
In addition to system cost and size, click and pop perfor-
mance is effected by the size of the input coupling capacitor,
C
i. A larger input coupling capacitor requires more charge to
reach its quiescent DC voltage (nominally 1/2 V
DD). This
charge comes from the output via the feedback and is apt to
create pops upon device enable. Thus, by minimizing the
capacitor size based on necessary low frequency response,
turn-on pops can be minimized.
Besides minimizing the input capacitor size, careful consid-
eration should be paid to the bypass capacitor value. Bypass
capacitor, C
B, is the most critical component to minimize
turn-on pops since it determines how fast the LM4893 turns
on. The slower the LM4893’s outputs ramp to their quiescent
DC voltage (nominally 1/2 V
DD), the smaller the turn-on pop.
Choosing C
B equal to 1.0 F along with a small value of Ci
(in the range of 0.1 F to 0.39 F), should produce a virtually
clickless and popless shutdown function. While the device
will function properly, (no oscillations or motorboating), with
C
B equal to 0.1 F, the device will be much more susceptible
to turn-on clicks and pops. Thus, a value of C
B equal to
1.0 F is recommended in all but the most cost sensitive
designs.
Figure 2 shows the LM4893’s turn-on characteristics when
coming out of shutdown mode. Trace B is the differential
output signal across a BTL 8
load. The LM4893’s active-
low SHUTDOWN pin is driven by the logic signal shown in
Trace A. Trace C is the Vo1- output signal and Trace D is the
Vo2+ output signal. A shown in Figure 2, the differential
output signal Trace B appears just as Trace A transitions
from logic low to logic high (turn-on condition).
AUDIO POWER AMPLIFIER DESIGN
A 1W/8
AUDIO AMPLIFIER
Given:
Power Output
1 Wrms
Load Impedance
8
Input Level
1 Vrms
Input Impedance
20 k
Bandwidth
100 Hz–20 kHz ± 0.25 dB
A designer must first determine the minimum supply rail to
obtain the specified output power. By extrapolating from the
Output Power vs Supply Voltage graphs in the Typical Per-
formance Characteristics section, the supply rail can be
easily found. A second way to determine the minimum sup-
ply rail is to calculate the required V
opeak using Equation 2
and add the output voltage. Using this method, the minimum
supply voltage would be (V
opeak +(VODTOP +VODBOT)), where
V
ODBOT and VODTOP are extrapolated from the Dropout Volt-
age vs Supply Voltage curve in the Typical Performance
Characteristics section.
(2)
5V is a standard voltage, in most applications, chosen for the
supply rail. Extra supply voltage creates headroom that al-
lows the LM4893 to reproduce peaks in excess of 1W with-
out producing audITLe distortion. At this time, the designer
must make sure that the power supply choice along with the
output impedance does not violate the conditions explained
in the Power Dissipation section.
Once the power dissipation equations have been addressed,
the required differential gain can be determined from Equa-
tion 3.
(3)
A
VD =(Rf/Ri)2
From Equation 3, the minimum A
VD is 2.83; use AVD =3.
Since the desired input impedance was 20 k
, and with a
A
VD of 3, a ratio of 1.5:1 of Rf to Ri results in an allocation of
R
i =20k
and R
f =30k
. The final design step is to
address the bandwidth requirements which must be stated
as a pair of 3 dB frequency points. Five times away from a
3 dB point is 0.17 dB down from passband response which
is better than the required ±0.25 dB specified.
f
L = 100 Hz/5 = 20 Hz
f
H =20kHz*5=100 kHz
As stated in the External Components section, R
i in con-
junction with C
i create a highpass filter.
C
i
≥ 1/(2π*20 k*20 Hz) = 0.397 F; use 0.39 F
The high frequency pole is determined by the product of the
desired frequency pole, f
H, and the differential gain, AVD.
With a A
VD = 3 and fH = 100 kHz, the resulting GBWP =
300 kHz which is much smaller than the LM4893 GBWP of
10 MHz. This figure displays that if a designer has a need to
design an amplifier with a higher differential gain, the
LM4893 can still be used without running into bandwidth
limitations.
20038097
FIGURE 2. LM4893 Turn-on Characteristics
Differential output signal (Trace B) is devoid of
transients. The SHUTDOWN pin is driven by a
shutdown signal (Trace A). The inverting output (Trace
C) and the non-inverting output (Trace D) are applied
across an 8
BTL load.
LM4893
www.national.com
13
相關PDF資料 |
PDF描述 |
|---|---|
| LM4894ITLX/NOPB | 1 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA9 |
| LM4894ITL/NOPB | 1 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA9 |
| LM4894LDX/NOPB | 1.4 W, 1 CHANNEL, AUDIO AMPLIFIER, DSO10 |
| LM4894LD/NOPB | 1.4 W, 1 CHANNEL, AUDIO AMPLIFIER, DSO10 |
| LM4894MM/NOPB | 1 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO10 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM4893MA | 制造商:Texas Instruments 功能描述:AMP, POWER AUDIO, 1.1W, SMD, SOIC8 |
| LM4893MA/NOPB | 功能描述:IC AMP AUDIO PWR 1.1W MONO 8SOIC RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:Boomer® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機，2-通道（立體聲） 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C，麥克風，靜音，短路保護，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) |
| LM4893MABD | 功能描述:BOARD EVALUATION LM4893MA RoHS:否 類別:編程器，開發系統 >> 評估板 - 音頻放大器 系列:Boomer® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- |
| LM4893MM | 制造商:Texas Instruments 功能描述:AMP AUDIO POWER 1.1W SMD LLP-10 |
| LM4893MM/NOPB | 功能描述:IC AMP AUDIO PWR 1.1W AB 10MSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:Boomer® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機，2-通道（立體聲） 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C，麥克風，靜音，短路保護，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。