參數資料
型號： LM4890ITLX
廠商： NATIONAL SEMICONDUCTOR CORP
元件分類： 音頻／視頻放大
英文描述： 1 Watt Audio Power Amplifier
中文描述： 1 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA9
封裝： MICRO, SMD-9
文件頁數： 19/31頁
文件大?。?/td> 1208K
代理商： LM4890ITLX
Application Information
(Continued)
SHUTDOWN OUTPUT IMPEDANCE
For R
f
= 20k ohms:
Z
OUT1
(between Out1 and GND) = 10k||50k||R
f
= 6k
Z
OUT2
(between Out2 and GND) = 10k||(40k+(10k||R
f
)) =
8.3k
Z
OUT1-2
(between Out1 and Out2) = 40k||(10k+(10k||R
f
)) =
The -3dB roll off for these measurements is 600kHz
PROPER SELECTION OF EXTERNAL COMPONENTS
Proper selection of external components in applications us-
ing integrated power amplifiers is critical to optimize device
and system performance. While the LM4890 is tolerant of
external component combinations, consideration to compo-
nent values must be used to maximize overall system qual-
ity.
The LM4890 is unity-gain stable which gives the designer
maximum system flexibility. The LM4890 should be used in
low gain configurations to minimize THD+N values, and
maximize the signal to noise ratio. Low gain configurations
require large input signals to obtain a given output power.
Input signals equal to or greater than 1Vrms are available
from sources such as audio codecs. Please refer to the
section,
Audio Power Amplifier Design
, for a more com-
plete explanation of proper gain selection.
Besides gain, one of the major considerations is the closed-
loop bandwidth of the amplifier. To a large extent, the band-
width is dictated by the choice of external components
shown in
Figure 1
. The input coupling capacitor, C
, forms a
first order high pass filter which limits low frequency re-
sponse. This value should be chosen based on needed
frequency response for a few distinct reasons.
Selection Of Input Capacitor Size
Large input capacitors are both expensive and space hungry
for portable designs. Clearly, a certain sized capacitor is
needed to couple in low frequencies without severe attenu-
ation. But in many cases the speakers used in portable
systems, whether internal or external, have little ability to
reproduce signals below 100Hz to 150Hz. Thus, using a
large input capacitor may not increase actual system perfor-
mance.
In addition to system cost and size, click and pop perfor-
mance is effected by the size of the input coupling capacitor,
C
IN
. A larger input coupling capacitor requires more charge
to reach its quiescent DC voltage (nominally 1/2 V
DD
). This
charge comes from the output via the feedback and is apt to
create pops upon device enable. Thus, by minimizing the
capacitor size based on necessary low frequency response,
turn-on pops can be minimized.
Besides minimizing the input capacitor size, careful consid-
eration should be paid to the bypass capacitor value. Bypass
capacitor, C
, is the most critical component to mini-
mize turn-on pops since it determines how fast the LM4890
turns on. The slower the LM4890’s outputs ramp to their
quiescent DC voltage (nominally 1/2V
), the smaller the
turn-on pop. Choosing C
equal to 1.0μF along with a
small value of C
IN
, (in the range of 0.1μF to 0.39μF), should
produce a virtually clickless and popless shutdown function.
While the device will function properly, (no oscillations or
motorboating), with C
equal to 0.1μF, the device will
be much more susceptible to turn-on clicks and pops. Thus,
a value of C
equal to 1.0μF is recommended in all but
the most cost sensitive designs.
AUDIO POWER AMPLIFIER DESIGN
A 1W/8
AUDIO AMPLIFIER
Given:
Power Output
Load Impedance
Input Level
Input Impedance
Bandwidth
1 Wrms
8
1 Vrms
20 k
100 Hz–20 kHz
±
0.25 dB
A designer must first determine the minimum supply rail to
obtain the specified output power. By extrapolating from the
Output Power vs Supply Voltage graphs in the
Typical Per-
formance Characteristics
section, the supply rail can be
easily found. A second way to determine the minimum sup-
ply rail is to calculate the required V
opeak
using Equation 2
and add the output voltage. Using this method, the minimum
supply voltage would be (V
+ (V
+ V
)), where
V
and V
are extrapolated from the Dropout Volt-
age vs Supply Voltage curve in the
Typical Performance
Characteristics
section.
(2)
5V is a standard voltage which in most applications is cho-
sen for the supply rail. Extra supply voltage creates head-
room that allows the LM4890 to reproduce peaks in excess
of 1W without producing audible distortion. At this time, the
designer must make sure that the power supply choice along
with the output impedance does not violate the conditions
explained in the
Power Dissipation
section.
Once the power dissipation equations have been addressed,
the required differential gain can be determined from Equa-
tion 3.
(3)
R
f
/R
IN
= A
VD
/2
From Equation 3, the minimum A
VD
is 2.83; use A
VD
= 3.
Since the desired input impedance is 20 k
, and with anA
gain of 3, a ratio of 1.5:1 of R
f
to R
results in an allocation
of R
= 20 k
and R
= 30 k
. The final design step is to
address the bandwidth requirements which must be stated
as a pair of 3 dB frequency points. Five times away from a
3 dB point is 0.17 dB down from passband response which
is better than the required
±
0.25 dB specified.
f
L
= 100Hz/5 = 20Hz
f
H
= 20kHz * 5 = 100kHz
L
www.national.com
19
相關PDF資料
PDF描述
LM4890LD 1 Watt Audio Power Amplifier
LM4890MM 1 Watt Audio Power Amplifier
LM4890M 1 Watt Audio Power Amplifier
LM4890ITL 1 Watt Audio Power Amplifier
LM4890IBL 1 Watt Audio Power Amplifier
相關代理商/技術參數
參數描述
LM4890ITLX/NOPB 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
LM4890ITP 制造商:Texas Instruments 功能描述:AMP AUDIO CELLULAR 1W SMD 4890
LM4890ITP/NOPB 功能描述:IC AMP AUDIO PWR 1W MONO 8USMD RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:Boomer® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機，2-通道（立體聲） 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C，麥克風，靜音，短路保護，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR)
LM4890ITPX/NOPB 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
LM4890LD 制造商:NSC 制造商全稱:National Semiconductor 功能描述:1 Watt Audio Power Amplifier
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*