- 您現在的位置：買賣IC網 > PDF目錄358867 > LM4889 (National Semiconductor Corporation) 1 Watt Audio Power Amplifier PDF資料下載
參數資料
| 型號： | LM4889 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | 1 Watt Audio Power Amplifier |
| 中文描述： | 1瓦音頻功率放大器 |
| 文件頁數： | 9/19頁 |
| 文件大小： | 763K |
| 代理商： | LM4889 |
Application Information
BRIDGE CONFIGURATION EXPLANATION
As shown in
Figure 1
, the LM4889 has two operational
amplifiers internally, allowing for a few different amplifier
configurations. The first amplifier’s gain is externally config-
urable, while the second amplifier is internally fixed in a
unity-gain, inverting configuration. The closed-loop gain of
the first amplifier is set by selecting the ratio of R
f
to R
i
while
the second amplifier’s gain is fixed by the two internal 20k
resistors.
Figure 1
shows that the output of amplifier one
serves as the input to amplifier two which results in both
amplifiers producing signals identical in magnitude, but out
of phase by 180. Consequently, the differential gain for the
IC is
A
VD
= 2 *(R
f
/R
i
)
By driving the load differentially through outputs Vo1 and
Vo2, an amplifier configuration commonly referred to as
“bridged mode” is established. Bridged mode operation is
different from the classical single-ended amplifier configura-
tion where one side of the load is connected to ground.
A bridge amplifier design has an advantage over the single-
ended configuration, as it provides differential drive to the
load, thus doubling output swing for a specified supply volt-
age. Four times the output power is possible as compared to
a single-ended amplifier under the same conditions. This
increase in attainable output power assumes that the ampli-
fier is not current limited or clipped. In order to choose an
amplifier’s closed-loop gain without causing excessive clip-
ping, please refer to the
Audio Power Amplifier Design
section.
A bridge configuration, such as the one used in LM4889,
also creates a second advantage over single-ended amplifi-
ers. Since the differential outputs, Vo1 and Vo2, are biased
at half-supply, no net DC voltage exists across the load. This
eliminates the need for an output coupling capacitor which is
required in a single supply, single-ended amplifier configura-
tion. Without an output coupling capacitor, the half-supply
bias across the load would result in both increased internal
IC power dissipation and also possible loudspeaker damage.
POWER DISSIPATION
Power dissipation is a major concern when designing a
successful amplifier, whether the amplifier is bridged or
single-ended. A direct consequence of the increased power
delivered to the load by a bridge amplifier is an increase in
internal power dissipation. Since the LM4889 has two opera-
tional amplifiers in one package, the maximum internal
power dissipation is 4 times that of a single-ended amplifier.
The maximum power dissipation for a given application can
be derived from the power dissipation graphs or from Equa-
tion 1.
P
DMAX
= 4*(V
DD
)
2
/(2
π
2
R
L
)
It is critical that the maximum junction temperature T
of
150C is not exceeded. T
can be determined from the
power derating curves by using P
and the PC board foil
area. By adding additional copper foil, the thermal resistance
of the application can be reduced from a free air value of
150C/W, resulting in higher P
DMAX
. Additional copper foil
can be added to any of the leads connected to the LM4889.
It is especially effective when connected to V
DD
, G
ND
, and
the output pins. Refer to the application information on the
LM4889 reference design board for an example of good heat
sinking. If T
JMAX
still exceeds 150C, then additional
changes must be made. These changes can include re-
(1)
duced supply voltage, higher load impedance, or reduced
ambient temperature. Internal power dissipation is a function
of output power. Refer to the
Typical Performance Charac-
teristics
curves for power dissipation information for differ-
ent output powers and output loading.
POWER SUPPLY BYPASSING
As with any amplifier, proper supply bypassing is critical for
low noise performance and high power supply rejection. The
capacitor location on both the bypass and power supply pins
should be as close to the device as possible. Typical appli-
cations employ a 5V regulator with 10 μF tantalum or elec-
trolytic capacitor and a ceramic bypass capacitor which aid
in supply stability. This does not eliminate the need for
bypassing the supply nodes of the LM4889. The selection of
a bypass capacitor, especially C
, is dependent upon PSRR
requirements, click and pop performance (as explained in
the section,
Proper Selection of External Components
),
system cost, and size constraints.
SHUTDOWN FUNCTION
In order to reduce power consumption while not in use, the
LM4889 contains a shutdown pin to externally turn off the
amplifier’s bias circuitry. This shutdown feature turns the
amplifier off when a logic low is placed on the shutdown pin.
By switching the shutdown pin to ground, the LM4889 supply
current draw will be minimized in idle mode. While the device
will be disabled with shutdown pin voltages less than
0.5V
, the idle current may be greater than the typical
value of 0.1μA. (Idle current is measured with the shutdown
pin grounded).
In many applications, a microcontroller or microprocessor
output is used to control the shutdown circuitry to provide a
quick, smooth transition into shutdown.Another solution is to
use a single-pole, single-throw switch in conjunction with an
external pull-up resistor. When the switch is closed, the
shutdown pin is connected to ground and disables the am-
plifier. If the switch is open, then the external pull-up resistor
will enable the LM4889. This scheme guarantees that the
shutdown pin will not float thus preventing unwanted state
changes.
PROPER SELECTION OF EXTERNAL COMPONENTS
Proper selection of external components in applications us-
ing integrated power amplifiers is critical to optimize device
and system performance. While the LM4889 is tolerant of
external component combinations, consideration to compo-
nent values must be used to maximize overall system qual-
ity.
The LM4889 is unity-gain stable which gives the designer
maximum system flexibility. The LM4889 should be used in
low gain configurations to minimize THD+N values, and
maximize the signal to noise ratio. Low gain configurations
require large input signals to obtain a given output power.
Input signals equal to or greater than 1 Vrms are available
from sources such as audio codecs. Please refer to the
section,
Audio Power Amplifier Design
, for a more com-
plete explanation of proper gain selection.
Besides gain, one of the major considerations is the closed-
loop bandwidth of the amplifier. To a large extent, the band-
width is dictated by the choice of external components
shown in
Figure 1
. The input coupling capacitor, C
i
, forms a
first order high pass filter which limits low frequency re-
sponse. This value should be chosen based on needed
frequency response for a few reasons.
L
www.national.com
9
相關PDF資料 |
PDF描述 |
|---|---|
| LM4890IBLX | GT 3C 3#16S SKT RECP WALL RM |
| LM4890ITLX | 1 Watt Audio Power Amplifier |
| LM4890LD | 1 Watt Audio Power Amplifier |
| LM4890MM | 1 Watt Audio Power Amplifier |
| LM4890M | 1 Watt Audio Power Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM4889ITL | 功能描述:IC AMP AUDIO PWR 1W MONO 8USMD RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:Boomer® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機，2-通道（立體聲） 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C，麥克風，靜音，短路保護，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) |
| LM4889ITLX | 制造商:Texas Instruments 功能描述:Audio Amp Speaker 1-CH Mono 1W Class-AB 8-Pin uSMD T/R |
| LM4889ITLX/NOPB | 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| LM4889LD/NOPB | 功能描述:IC AMP AUDIO PWR 1W MONO 10LLP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:Boomer® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機，2-通道（立體聲） 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C，麥克風，靜音，短路保護，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) |
| LM4889MA | 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。