- 您現在的位置：買賣IC網 > PDF目錄10311 > LM4872IBPX (National Semiconductor)IC AMP AUDIO PWR 1W MONO 8USMD PDF資料下載
參數資料
| 型號： | LM4872IBPX |
| 廠商： | National Semiconductor |
| 文件頁數： | 7/17頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC AMP AUDIO PWR 1W MONO 8USMD |
| 標準包裝： | 3,000 |
| 系列： | Boomer® |
| 類型： | AB 類 |
| 輸出類型： | 1-通道（單聲道） |
| 在某負載時最大輸出功率 x 通道數量： | 1W x 1 @ 8 歐姆 |
| 電源電壓： | 2 V ~ 5.5 V |
| 特點： | 關閉，熱保護 |
| 安裝類型： | 表面貼裝 |
| 供應商設備封裝： | 8-uSMD |
| 封裝/外殼： | 8-VFBGA |
| 包裝： | 帶卷 (TR) |
| 其它名稱： | *LM4872IBPX |
Application Information (Continued)
Reference Design Board and PCB Layout Guidelines
PCB Layout Guidelines
This section provides practical guidelines for mixed signal
PCB layout that involves various digital/analog power and
ground traces. Designers should note that these are only
’rule-of-thumb’ recommendations and the actual results will
depend heavily on the final layout.
General Mixed Signal Layout Recommendation
Power and Ground Circuits
For 2 layer mixed signal design, it is important to isolate the
digital power and ground trace paths from the analog power
and ground trace paths. Star trace routing techniques (bring-
ing individual traces back to a central point rather than daisy
chaining traces together in a serial manner) can have a
major impact on low level signal performance. Star trace
routing refers to using individual traces to feed power and
ground to each circuit or even device. This technique will
take require a greater amount of design time but will not
increase the final price of the board. The only extra parts
required will be some jumpers.
Single-Point Power / Ground Connections
The analog power traces should be connected to the digital
traces through a single point (link). A ’Pi-filter’ can be helpful
in minimizing High Frequency noise coupling between the
analog and digital sections. It is further recommended to put
digital and analog power traces over the corresponding digi-
tal and analog ground traces to minimize noise coupling.
Placement of Digital and Analog Components
All digital components and high-speed digital signals traces
should be located as far away as possible from analog
components and circuit traces.
Avoiding Typical Design / Layout Problems
Avoid ground loops or running digital and analog traces
parallel to each other (side-by-side) on the same PCB layer.
When traces must cross over each other do it at 90 degrees.
Running digital and analog traces at 90 degrees to each
other from the top to the bottom side as much as possible will
minimize capacitive noise coupling and cross talk.
10123025
FIGURE 4. Reference Design Board
LM4872
www.national.com
14
相關PDF資料 |
PDF描述 |
|---|---|
| 17984-7PG-3ES | CONN RCPT 7POS PNL MNT PIN |
| VE-BN0-IW-B1 | CONVERTER MOD DC/DC 5V 100W |
| 62HB8FX | CONN RCPT 8CONT DIN SLD LOCKRING |
| VE-2NX-CU-S | CONVERTER MOD DC/DC 5.2V 200W |
| VI-2TH-MX-S | CONVERTER MOD DC/DC 52V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM4872ITP | 制造商:Texas Instruments 功能描述:AMP AUDIO 1W BOOMER SMD 4872 |
| LM4872ITP/NOPB | 功能描述:IC AMP AUDIO PWR 1W MONO 8USMD RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:Boomer® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機，2-通道（立體聲） 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C，麥克風，靜音，短路保護，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) |
| LM4872ITPX/NOPB | 制造商:Texas Instruments 功能描述: |
| LM4873 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Dual 2.1W Audio Amplifier Plus Stereo Headphone Function |
| LM4873_02 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Dual 2.1W Audio Amplifier Plus Stereo Headphone Function |
發布緊急采購，3分鐘左右您將得到回復。