- 您現在的位置：買賣IC網 > PDF目錄358866 > LM4855 (National Semiconductor Corporation) Boomer AUDIO POWER AMPLIFIER Integrated Audio Amplifier System PDF資料下載
參數資料
| 型號： | LM4855 |
| 廠商： | National Semiconductor Corporation |
| 元件分類： | 運動控制電子 |
| 英文描述： | Boomer AUDIO POWER AMPLIFIER Integrated Audio Amplifier System |
| 中文描述： | Boomer音頻功率放大器集成音頻放大器系統 |
| 文件頁數： | 18/24頁 |
| 文件大?。?/td> | 1116K |
| 代理商： | LM4855 |
APPLICATION INFORMATION
(Continued)
voltage, increase the load impedance, or reduce the ambient
temperature. If these measures are insufficient, a heat sink
can be added to reduce
θ
. The heat sink can be created
using additional copper area around the package, with con-
nections to the ground pin(s), supply pin and amplifier output
pins. External, solder attached SMT heatsinks such as the
Thermalloy 7106D can also improve power dissipation.
When adding a heat sink, the
θ
is the sum of
θ
,
θ
CS
, and
θ
. (
θ
is the junction-to-case thermal impedance,
θ
is
the case-to-sink thermal impedance, and
θ
is the sink-to-
ambient thermal impedance.) Refer to the Typical Perfor-
mance Characteristics curves for power dissipation informa-
tion at lower output power levels.
POWER SUPPLY BYPASSING
As with any power amplifier, proper supply bypassing is
critical for low noise performance and high power supply
rejection. Applications that employ a 5V regulator typically
use a 10μF in parallel with a 0.1μF filter capacitors to stabi-
lize the regulator’s output, reduce noise on the supply line,
and improve the supply’s transient response. However, their
presence does not eliminate the need for a local 1.0μF
tantalum bypass capacitance connected between the
LM4855’s supply pins and ground. Keep the length of leads
and traces that connect capacitors between the LM4855’s
power supply pin and ground as short as possible. Connect-
ing a 1μF capacitor, C
, between the BYPASS pin and
ground improves the internal bias voltage’s stability and
improves the amplifier’s PSRR. The PSRR improvements
increase as the bypass pin capacitor value increases. Too
large, however, increases turn-on time and can compromise
the amplifier’s click and pop performance. The selection of
bypass capacitor values, especially C
, depends on desired
PSRR requirements, click and pop performance (as ex-
plained in the section, Proper Selection of External Compo-
nents), system cost, and size constraints.
SELECTING EXTERNAL COMPONENTS
Input Capacitor Value Selection
Amplifying the lowest audio frequencies requires high value
input coupling capacitor (C
in Figure 2). A high value capaci-
tor can be expensive and may compromise space efficiency
in portable designs. In many cases, however, the speakers
used in portable systems, whether internal or external, have
little ability to reproduce signals below 150Hz. Applications
using speakers with this limited frequency response reap
little improvement by using large input capacitor.
The internal input resistor (R
i
) and the input capacitor (C
i
)
produce a high pass filter cutoff frequency that is found using
Equation (9).
f
c
= 1 / (2
π
R
i
C
i
)
(9)
As an example when using a speaker with a low frequency
limit of 150Hz, C
, using Equation (9) is 0.063μF. The 0.22μF
C
shown in Figure 1 allows the LM4855 to drive high effi-
ciency, full range speaker whose response extends below
40Hz.
Bypass Capacitor Value Selection
Besides minimizing the input capacitor size, careful consid-
eration should be paid to value of C
B
, the capacitor con-
nected to the BYPASS pin. Since C
determines how fast
the LM4855 settles to quiescent operation, its value is critical
when minimizing turn-on pops. The slower the LM4855’s
outputs ramp to their quiescent DC voltage (nominally V
/
2), the smaller the turn-on pop. Choosing C
equal to 1.0μF
along with a small value of C
i
(in the range of 0.1μF to
0.39μF), produces a click-less and pop-less shutdown func-
tion. As discussed above, choosing C
i
no larger than neces-
sary for the desired bandwidth helps minimize clicks and
pops. C
B
’s value should be in the range of 5 times to 7 times
the value of C
i
. This ensures that output transients are
eliminated when power is first applied or the LM4855 re-
sumes operation after shutdown.
L
www.national.com
18
相關PDF資料 |
PDF描述 |
|---|---|
| LM4857 | Stereo 1.2W Audio Sub-system with 3D Enhancement |
| LM4857GR | Stereo 1.2W Audio Sub-system with 3D Enhancement |
| LM4857ITL | Stereo 1.2W Audio Sub-system with 3D Enhancement |
| LM4857SP | Stereo 1.2W Audio Sub-system with 3D Enhancement |
| LM4859 | Circular Connector; MIL SPEC:MIL-C-5015; Body Material:Metal; Series:GT; No. of Contacts:47; Connector Shell Size:40; Connecting Termination:Crimp; Circular Shell Style:Wall Mount Receptacle; Body Style:Straight |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM48555 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Ceramic Speaker Driver |
| LM48555TL | 制造商:Texas Instruments 功能描述:Audio Amp Speaker 1-CH Mono Class-AB 12-Pin uSMD T/R 制造商:Texas Instruments 功能描述:IC AMP POWER AUDIO SMD |
| LM48555TL/NOPB | 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| LM48555TLBD | 功能描述:音頻 IC 開發工具 LM48555TL EVAL BOARD RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| LM48555TLX/NOPB | 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。