- 您現在的位置：買賣IC網 > PDF目錄385486 > LM4839MTE (NATIONAL SEMICONDUCTOR CORP) Stereo 2W Audio Power Amplifiers with DC Volume Control, Bass Boost, and Input Mux PDF資料下載
參數資料
| 型號： | LM4839MTE |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 音頻控制 |
| 英文描述： | Stereo 2W Audio Power Amplifiers with DC Volume Control, Bass Boost, and Input Mux |
| 中文描述： | 2 CHANNEL(S), TONE CONTROL CIRCUIT, PDSO28 |
| 封裝： | TSSOP-28 |
| 文件頁數： | 20/34頁 |
| 文件大?。?/td> | 1104K |
| 代理商： | LM4839MTE |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁
AUDIO POWER AMPLIFIER
DESIGN
Audio Amplifier Design: Driving 1W into an 8
Load
The following are the desired operational parameters:
Power Output:
Load Impedance:
Input Level:
Input Impedance:
Bandwidth:
1 W
RMS
8
1 V
RMS
20 k
100 Hz20 kHz
±
0.25 dB
The design begins by specifying the minimum supply voltage
necessary to obtain the specified output power. One way to
find the minimum supply voltage is to use the Output Power
vs Supply Voltage curve in the
Typical Performance Char-
acteristics
section. Another way, using Equation (11), is to
calculate the peak output voltage necessary to achieve the
desired output power for a given load impedance. To ac-
count for the amplifier’s dropout voltage, two additional volt-
ages, based on the Dropout Voltage vs Supply Voltage in the
Typical Performance Characteristics
curves, must be
added to the result obtained by Equation (11). The result is
Equation (12).
(10)
V
DD
≥
(V
OUTPEAK
+ (V
OD
TOP
+ V
OD
BOT
))
(11)
The Output Power vs Supply Voltage graph for an 8
load
indicates a minimum supply voltage of 4.6V. This is easily
met by the commonly used 5V supply voltage. The additional
voltage creates the benefit of headroom, allowing the
LM4839 to produce peak output power in excess of 1W
without clipping or other audible distortion. The choice of
supply voltage must also not create a situation that violates
of maximum power dissipation as explained above in the
Power Dissipation
section.
After satisfying the LM4839’s power dissipation require-
ments, the minimum differential gain needed to achieve 1W
dissipation in an 8
load is found using Equation (13).
(12)
Thus, a minimum overall gain of 2.83 allows the LM4839’s to
reach full output swing and maintain low noise and THD+N
performance.
The last step in this design example is setting the amplifier’s
3dB frequency bandwidth. To achieve the desired
±
0.25dB
pass band magnitude variation limit, the low frequency re-
sponse must extend to at least one-fifth the lower bandwidth
limit and the high frequency response must extend to at least
five times the upper bandwidth limit. The gain variation for
both response limits is 0.17dB, well within the
±
0.25dB
desired limit. The results are an
f
L
= 100Hz/5 = 20Hz
(13)
and an
f
H
= 20kHz x 5 = 100kHz
(14)
As mentioned in the
Selecting Proper External Compo-
nents
section, R
(Right & Left) and C
(Right & Left) create
a highpass filter that sets the amplifier’s lower bandpass
frequency limit. Find the coupling capacitor’s value using
Equation (17).
C
i
≥
1/(2
π
R
i
f
L
)
(15)
The result is
1/(2
π
*
20k
*
20Hz) = 0.397μF
(16)
Use a 0.39μF capacitor, the closest standard value.
The product of the desired high frequency cutoff (100kHz in
this example) and the differential gain A
VD
, determines the
upper passband response limit. With A
= 3 and f
=
100kHz, the closed-loop gain bandwidth product (GBWP) is
300kHz. This is less than the LM4839’s 3.5MHz GBWP. With
this margin, the amplifier can be used in designs that require
more differential gain while avoiding performance,restricting
bandwidth limitations.
RECOMMENDED PRINTED
CIRCUIT BOARD LAYOUT
Figures 4 through 8 show the recommended four-layer PC
board layout that is optimized for the 8-pin LQ-packaged
LM4839 and associated external components. This circuit is
designed for use with an external 5V supply and 4
speak-
ers.
This circuit board is easy to use. Apply 5V and ground to the
board’s V
and GND pads, respectively. Connect 4
speakers between the board’s OUTA and +OUTA and
OUTB and +OUTB pads.
L
www.national.com
20
相關PDF資料 |
PDF描述 |
|---|---|
| LM4840 | RES 20.5 OHM 1/10W 1% 0603 SMD |
| LM4840LQ | Stereo 2W Audio Power Amplifiers with Digital Volume Control and Input Mux |
| LM4840MH | Stereo 2W Audio Power Amplifiers with Digital Volume Control and Input Mux |
| LM4840MT | Stereo 2W Audio Power Amplifiers with Digital Volume Control and Input Mux |
| LM4841 | Stereo 2W Amplifiers with DC Volume Control, Transient Free Outputs, and Cap-less Headphone Drive |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM4839MTE/NOPB | 功能描述:IC AMP AUDIO PWR 2.2W AB 28TSSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:Boomer® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機，2-通道（立體聲） 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C，麥克風，靜音，短路保護，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) |
| LM4840 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Stereo 2W Audio Power Amplifiers with Digital Volume Control and Input Mux |
| LM4840LQ | 制造商:Texas Instruments 功能描述:AMP AUDIO POWER DC VOLT LLP-28 |
| LM4840LQ/NOPB | 功能描述:IC AMP AUDIO PWR 2.2W STER 28LLP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:Boomer® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機，2-通道（立體聲） 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C，麥克風，靜音，短路保護，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) |
| LM4840MH | 制造商:Texas Instruments 功能描述:AMP AUDIO STEREO 2W SMD TSSOP28 |
發布緊急采購，3分鐘左右您將得到回復。