參數資料
型號： LM4831VFX
廠商： NATIONAL SEMICONDUCTOR CORP
元件分類： 消費家電
英文描述： SPECIALTY CONSUMER CIRCUIT, PQFP44
封裝： TQFP-44
文件頁數： 9/13頁
文件大?。?/td> 575K
代理商： LM4831VFX
Pin Descriptions
VDDA
This is the analog power supply pin
which powers all internal circuitry, with
the exceptions of the output amplifiers
and the digital logic in the Beep and
Switching circuit sections. This pin
should be connected to the same
supply voltage as the two VDDD pins
(typically 5V), but have a separate
ground return path to the supply
ground to minimize interaction with the
high current amplifier returns and
digital switching noise. In addition, this
pin should be bypassed with a 0.01
F–0.1 F capacitor.
VDDD
These pins are the “digital” and high
current power supply pins which
power the stereo bridged output
amplifier and the digital logic in the
Beep and Switching circuit sections.
These pins should be connected to
the same supply voltage as the VDDA
pin (typically 5V), but have a separate
return path to the supply to avoid
interferring with low level signals. In
addition, this pin should be bypassed
with a 0.01 F–0.1 F capacitor. At
the power supply connection, a bulk
storage capacitor of at least 10 F will
reduce the instantaneous current
demanded from the power supply.
GNDA,
GNDD,
GNDM
These are the power supply ground
pins. GNDA is the ground pin for the
low current analog circuitry. The two
GNDD pins are for the digital logic
and bridged output amplifiers. GNDM
is the ground for the microphone
amplifier. Make sure that the high
current GNDD paths are not returned
through the low current GNDM or
GNDA paths. These four ground pins
should be star-grounded at a stable,
low-impedance, noise-free system
ground.
BYPASS
This voltage at this pin is nominally
1/2 VDDD and is created by an
internal 50 k
resistor divider. This
node should be bypassed with a
capacitor value from 0.1 F-1.0 F.
Increasing the capacitor value will
increase the ramp time of the
amplifiers, thereby improving turn-on
pop performance. 0.1F is typical for
the bypass capacitor. In addition, a 1
M
resistor from the bypass pin to the
positive supply is shown in Figure 3.
This resistor guarantees that the
LM4831 will turn-on if the device is
powered up with both the PWRDWN
and DS-IN pins high. If the the
LM4831 will never enter that state,
then the 1M
resistor can be
removed.
HP-IN
This pin places the output power
amplifier in “headphone” mode. If
HP-IN is low, the amplifier is in
bridged mode and the 2:1 mux passes
the input on the EQ_IN pin. If HP-IN is
high, the amplifier is in single-ended
mode and the 2:1 mux passes the
output of the mixing stage.
Single-ended mode places the
non-inverting amplifier in the output
amplifiers into a high impedance state.
HP-IN also has priority over the DS-IN
pin, so if HP-IN and DS-IN are both
high, the device is in single-ended
mode and the stereo line out amplifier
is in a high-impedance state.
DS-IN
This pin is used to put the LM4831
into “docking-station” mode and
control the line out drivers and the
state of the internal 2:1 analog
multiplexer. If DS-IN is high, the
stereo line out amplifier is on and the
stereo bridged amplifier is in a high
impedance state. Asserting the DS-IN
pin also changes the 2:1 analog
multiplexer output from the stereo
signal on the L_EQIN and R_EQIN
pins to the internal path from the
stereo input mixer.
LM4831
www.national.com
5
相關PDF資料
PDF描述
LM4832M/NOPB 2 CHANNEL(S), TONE CONTROL CIRCUIT, PDSO28
LM4832MT/NOPB 2 CHANNEL(S), TONE CONTROL CIRCUIT, PDSO28
LM4834MDC 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, UUC
LM4834MWC 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, UUC
LM4834MSX/NOPB 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO28
相關代理商/技術參數
參數描述
LM4832 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Digitally Controlled Tone and Volume Circuit with Stereo Audio Power Amplifier, Microphone Preamp Stage and National 3D Sound
LM4832M 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Digitally Controlled Tone and Volume Circuit with Stereo Audio Power Amplifier, Microphone Preamp Stage and National 3D Sound
LM4832M/NOPB 功能描述:IC AMP AUDIO PWR .25W AB 28SOIC RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:Boomer® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機，2-通道（立體聲） 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C，麥克風，靜音，短路保護，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR)
LM4832MT/NOPB 功能描述:IC AMP AUDIO PWR .25W AB 28TSSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:Boomer® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機，2-通道（立體聲） 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C，麥克風，靜音，短路保護，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR)
LM4832MTX/NOPB 功能描述:IC AMP AUDIO PWR .25W AB 28TSSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:Boomer® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機，2-通道（立體聲） 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C，麥克風，靜音，短路保護，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*