參數資料
型號: LM4831
廠商: National Semiconductor Corporation
英文描述: Multimedia Computer Audio Chip
中文描述: 多媒體計算機音頻芯片
文件頁數: 7/12頁
文件大小: 575K
代理商: LM4831
Pin Descriptions
(Continued)
MIC+IN
This pin is the positive input of the
microphone amplifier. The microphone
amplifier is typically configured as an
inverting amplifier, so this pin should
be connected to the BYPASS pin to
properly bias the amplifier. Further,
this pin should be individually
bypassed with a capacitor of
0.01μF–0.1 μF.
MICIN
This pin is the inverting input for the
microphone amplifier. Because the
microphone amplifier is typically used
as an inverting amplifier, this pin
should be capacitor coupled to the
input signal.
MIC OUT
This pin is the microphone amplifier
output. If this pin is to be connected to
any chips other than the LM4831, it
should be capacitor coupled to the
load.
BEEP A,
BEEP B,
BEEP C,
BEEP D
These four pins are used to “wake up”
the LM4831 for a specified amount of
time (dictated by the parallel resistor
and capacitor connected to the RC
pin). If the device is in shutdown and
an edge appears at any of the four
BEEP pins, then the device will
power-up, pass the sound, and then
power-down again.
BEEP OUT
This pin outputs the result of an
exclusive-or of the four BEEP inputs.
BEEP OUT connects back to the
Audio Codec as a status pin.
RC
This pin is connected to an external
resistor-capacitor network which sets
the on-time for a beep request.
Typically, a 0.1μF capacitor is
paralleled with a 1–10M
resistor.
Typical Performance Characteristic
Supply Current vs
Supply Voltage
DS100057-31
Power Derating Curve
DS100057-23
THD+N vs Frequency
DS100057-5
THD+N vs Frequency
DS100057-4
THD+N vs Frequency
DS100057-29
www.national.com
7
相關PDF資料
PDF描述
LM4832MX Digitally Controlled Tone and Volume Circuit with Stereo Audio Power Amplifier, Microphone Preamp Stage and National 3D Sound
LM4832 Digitally Controlled Tone and Volume Circuit with Stereo Audio Power Amplifier, Microphone Preamp Stage and National 3D Sound
LM4832M Digitally Controlled Tone and Volume Circuit with Stereo Audio Power Amplifier, Microphone Preamp Stage and National 3D Sound
LM4832N Digitally Controlled Tone and Volume Circuit with Stereo Audio Power Amplifier, Microphone Preamp Stage and National 3D Sound
LM4834 1.75W Audio Power Amplifier with DC Volume Control and Microphone Preamp
相關代理商/技術參數
參數描述
LM4831 WAF 制造商:Texas Instruments 功能描述:
LM48310 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Ultra-Low EMI, Filterless, 2.6W, Mono, Class D Audio Power Amplifier with E2S
LM48310SD 制造商:Texas Instruments 功能描述:Audio Amp Speaker 1-CH Mono 2.6W Class-D 10-Pin LLP EP T/R
LM48310SD/NOPB 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
LM48310SDBD 功能描述:音頻 IC 開發工具 LM48310SD EVAL BOARD RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V