- 您現在的位置：買賣IC網 > PDF目錄30752 > LM4820MX-6/NOPB (NATIONAL SEMICONDUCTOR CORP) 1 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8 PDF資料下載
參數資料
| 型號： | LM4820MX-6/NOPB |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 1 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
| 封裝： | SOIC-8 |
| 文件頁數： | 7/18頁 |
| 文件大?。?/td> | 539K |
| 代理商： | LM4820MX-6/NOPB |
Application Information (Continued)
Mono LM4820-6 Reference Design Boards
Bill of Material for all 3 Demo Boards
Item
Part Number
Part Description
Qty
Ref Designator
1
551011208-001
LM4820-6 Mono Reference Design
Board
1
10
482911183-001
LM4820-6 Audio AMP
1
U1
20
151911207-001
Tant Cap 1uF 16V 10
1
C1
21
151911207-002
Cer Cap 0.39uF 50V Z5U 20% 1210
1
C2
25
152911207-001
Tant Cap 1uF 16V 10
1
C3
30
472911207-001
Res 20K Ohm 1/10W 5
3
R1
35
210007039-002
Jumper Header Vertical Mount 2X1
0.100
2J1
PCB LAYOUT GUIDELINES
This section provides practical guidelines for mixed signal
PCB layout that involves various digital/analog power and
ground traces. Designers should note that these are only
’rule-of-thumb’ recommendations and the actual results will
depend heavily on the final layout.
General Mixed Signal Layout Recommendation
Power and Ground Circuits
For 2 layer mixed signal design, it is important to isolate the
digital power and ground trace paths from the analog power
and ground trace paths. Star trace routing techniques (bring-
ing individual traces back to a central point rather than daisy
chaining traces together in a serial manner) can have a
major impact on low level signal performance. Star trace
routing refers to using individual traces to feed power and
ground to each circuit or even device. This technique will
take require a greater amount of design time but will not
increase the final price of the board. The only extra parts
required will be some jumpers.
Single-Point Power / Ground Connections
The analog power traces should be connected to the digital
traces through a single point (link). A ’Pi-filter’ can be helpful
in minimizing High Frequency noise coupling between the
analog and digital sections. It is further recommended to put
digital and analog power traces over the corresponding digi-
tal and analog ground traces to minimize noise coupling.
Placement of Digital and Analog Components
All digital components and high-speed digital signals traces
should be located as far away as possible from analog
components and circuit traces.
Avoiding Typical Design / Layout Problems
Avoid ground loops or running digital and analog traces
parallel to each other (side-by-side) on the same PCB layer.
When traces must cross over each other do it at 90 degrees.
Running digital and analog traces at 90 degrees to each
other from the top to the bottom side as much as possible will
minimize capacitive noise coupling and cross talk.
LM4820-6
www.national.com
15
相關PDF資料 |
PDF描述 |
|---|---|
| LM4820MX-6 | 1 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
| LM4820MM-6/NOPB | 1 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
| LM4820M-6/NOPB | 1 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
| LM4820IBP-6/NOPB | 1 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA8 |
| LM4820IBPX-6/NOPB | 1 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM4830 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Two-Way Audio Amplification System with Volume Control |
| LM4830A WAF | 制造商:Texas Instruments 功能描述: |
| LM4830M | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| LM4830MX | 制造商:Texas Instruments 功能描述: |
| LM4830N | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
發布緊急采購，3分鐘左右您將得到回復。