- 您現在的位置：買賣IC網 > PDF目錄358866 > LM4781 (National Semiconductor Corporation) Overture⑩ Audio Power Amplifier Series 3 Channel 35W Audio Power Amplifier with Mute PDF資料下載
參數資料
| 型號： | LM4781 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | Overture⑩ Audio Power Amplifier Series 3 Channel 35W Audio Power Amplifier with Mute |
| 中文描述： | 序曲⑩音頻功率放大器系列三通道35W的音頻功率放大器靜音 |
| 文件頁數： | 8/25頁 |
| 文件大?。?/td> | 1125K |
| 代理商： | LM4781 |
External Components Description
(Figures 1-5)
Components
R
B
Functional Description
1
Prevents current from entering the amplifier’s non-inverting input. This current may pass through to the load
during system power down, because of the amplifier’s low input impedance when the undervoltage circuitry
is off. This phenomenon occurs when the V
+
and V
-
supply voltages are below 1.5V.
Inverting input resistance. Along with R
f
, sets AC gain.
Feedback resistance. Along with R
i
, sets AC gain.
Feedback resistance. Works with Cf and Rf creating a lowpass filter that lowers AC gain at high
frequencies. The -3dB point of the pole occurs when: (R
f
- R
i
)/2 = R
f
// [1/(2
π
f
c
C
f
) + R
f2
] for the
Non-Inverting configuration shown in
Figure 5
.
Compensation capacitor. Works with R
f
and R
f2
to reduce AC gain at higher frequencies.
2
3
4
R
i
R
f
R
f2
(Note 16)
5
C
f
(Note 16)
C
C
(Note 16)
C
i
(Note 16)
C
S
6
Compensation capacitor. Reduces the gain at higher frequencies to avoid quasi-saturation oscillations of the
output transistor. Also suppresses external electromagnetic switching noise created from fluorescent lamps.
Feedback capacitor which ensures unity gain at DC. Along with R
i
also creates a highpass filter at f
c
=
1/(2
π
R
i
C
i
).
Provides power supply filtering and bypassing. Refer to the Supply Bypassing application section for proper
placement and selection of bypass capacitors.
Acts as a volume control by setting the input voltage level.
7
8
9
R
V
(Note 16)
R
IN
(Note 16)
10
Sets the amplifier’s input terminals DC bias point when C
IN
is present in the circuit. Also works with C
IN
to
create a highpass filter at f
C
= 1/(2
π
R
IN
C
IN
). If the value of R
IN
is too large, oscillations may be observed on
the outputs when the inputs are floating. Recommended values are 10k
to 47k
. Refer to
Figure 5
.
Input capacitor. Prevents the input signal’s DC offsets from being passed onto the amplifier’s inputs.
11
C
IN
(Note 16)
R
SN
(Note 16)
C
SN
(Note 16)
L (Note 16)
12
Works with C
SN
to stabilize the output stage by creating a pole that reduces high frequency instabilities.
13
Works with R
SN
to stabilize the output stage by creating a pole that reduces high frequency instabilities. The
pole is set at f
C
= 1/(2
π
R
SN
C
SN
). Refer to
Figure 5
.
Provides high impedance at high frequencies so that R may decouple a highly capacitive load and reduce
the Q of the series resonant circuit. Also provides a low impedance at low frequencies to short out R and
pass audio signals to the load. Refer to
Figure 5
.
Provides DC voltage biasing for the transistor Q1 in single supply operation.
Provides bias filtering for single supply operation.
Limits the voltage difference between the amplifier’s inputs for single supply operation. Refer to the
Clicks
and Pops
application section for a more detailed explanation of the function of R
INP
.
Provides input bias current for single supply operation. Refer to the
Clicks and Pops
application section for
a more detailed explanation of the function of R
BI
.
Establishes a fixed DC current for the transistor Q1 in single supply operation. This resistor stabilizes the
half-supply point along with C
A
.
Mute resistance set up to allow 0.5mA to be drawn from each MUTE pin to turn the muting function off.
→
R
M
is calculated using: R
M
≤
(|V
EE
| 2.6V)/l where l
≥
0.5mA. Refer to the Mute Attenuation vs Mute
Current curves in the Typical Performance Characteristics section.
Mute capacitance set up to create a large time constant for turn-on and turn-off muting.
Mute switch. When open or switched to GND, the amplifier will be in mute mode.
Reduces current flow between outputs that are caused by Gain or DC offset differences between the
amplifiers.
14
15
R (Note 16)
16
17
18
R
A
C
A
R
INP
(Note 16)
R
BI
19
20
R
E
21
R
M
22
23
24
C
M
S
1
R
OUT
Note 16:
Optional components dependent upon specific design requirements.
L
www.national.com
8
相關PDF資料 |
PDF描述 |
|---|---|
| LM4782TA | 3 Channel 25W Audio Power Amplifier with Mute and Standby |
| LM4782 | 3 Channel 25W Audio Power Amplifier with Mute and Standby |
| LM480261 | Medium Size Graphic Type LCD Module |
| LM4802B | Audio Power Amplifier with Boost Converter to Drive Ceramic Speakers |
| LM4802BLQ | Audio Power Amplifier with Boost Converter to Drive Ceramic Speakers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM4781TA | 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| LM4781TA/NOPB | 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| LM4781TABD | 功能描述:音頻 IC 開發工具 LM4871 EVAL BOARD RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| LM4781TABD/NOPB | 功能描述:音頻 IC 開發工具 LM4781TABD EVAL MOD RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| LM4782 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Overture Audio Power Amplifier Series 3 Channel 25W Audio Power Amplifier with Mute and Standby |
發布緊急采購，3分鐘左右您將得到回復。