- 您現在的位置：買賣IC網 > PDF目錄358866 > LM4780 (National Semiconductor Corporation) Audio Power Amplifier Series Stereo 60W, Mono 120W Audio Power Amplifier with Mute PDF資料下載
參數資料
| 型號： | LM4780 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | Audio Power Amplifier Series Stereo 60W, Mono 120W Audio Power Amplifier with Mute |
| 中文描述： | 音頻功率放大器系列立體聲60瓦，120瓦單聲道音頻功率放大器與靜音 |
| 文件頁數： | 19/24頁 |
| 文件大?。?/td> | 1030K |
| 代理商： | LM4780 |
Application Information
(Continued)
20058698
The load current I
will be much larger than input bias current
I
, thus V
will follow the output voltage directly, i.e. in phase.
Therefore the voltage appearing at the non-inverting input is
effectively positive feedback and the circuit may oscillate. If
there was only one device to worry about then the values of
R
1
and R
2
would probably be small enough to be ignored;
however, several devices normally comprise a total system.
Any ground return of a separate device, whose output is in
phase, can feedback in a similar manner and cause insta-
bilities. Out of phase ground loops also are troublesome,
causing unexpected gain and phase errors.
The solution to most ground loop problems is to always use
a single-point ground system, although this is sometimes
impractical. The third figure above is an example of a single-
point ground system.
The single-point ground concept should be applied rigor-
ously to all components and all circuits when possible. Vio-
lations of single-point grounding are most common among
printed circuit board designs, since the circuit is surrounded
by large ground areas which invite the temptation to run a
device to the closest ground spot. As a final rule, make all
ground returns low resistance and low inductance by using
large wire and wide traces.
Occasionally, current in the output leads (which function as
antennas) can be coupled through the air to the amplifier
input, resulting in high-frequency oscillation. This normally
happens when the source impedance is high or the input
leads are long. The problem can be eliminated by placing a
small capacitor, C
C
, (on the order of 50pF to 500pF) across
the LM4780 input terminals. Refer to the
External Compo-
nents Description
section relating to component interaction
with C
f
.
REACTIVE LOADING
It is hard for most power amplifiers to drive highly capacitive
loads very effectively and normally results in oscillations or
ringing on the square wave response. If the output of the
LM4780 is connected directly to a capacitor with no series
resistance, the square wave response will exhibit ringing if
the capacitance is greater than about 0.2μF. If highly capaci-
tive loads are expected due to long speaker cables, a
method commonly employed to protect amplifiers from low
impedances at high frequencies is to couple to the load
through a 10
resistor in parallel with a 0.7μH inductor. The
inductor-resistor combination as shown in the
Figure 5
iso-
lates the feedback amplifier from the load by providing high
output impedance at high frequencies thus allowing the 10
resistor to decouple the capacitive load and reduce the Q of
the series resonant circuit. The LR combination also pro-
vides low output impedance at low frequencies thus shorting
out the 10
resistor and allowing the amplifier to drive the
series RC load (large capacitive load due to long speaker
cables) directly.
INVERTING AMPLIFIER APPLICATION
The inverting amplifier configuration may be used instead of
the more common non-inverting amplifier configuration
shown in
Figure 1
. The inverting amplifier can have better
THD+N performance and eliminates the need for a large
capacitor (Ci) reducing cost and space requirements. The
values show in
Figure 6
are only one example of an amplifier
with a gain of 20V/V (Gain = -R
/R
). For different resistor
values, the value of R
B
should be eqaul to the parallel
combination of R
f
and Ri.
If the DC blocking input capacitor (C
) is used as shown, the
lower -3dB point is found using Equation (8) as discussed in
the
Proper Selection of External Components
section.
L
www.national.com
19
相關PDF資料 |
PDF描述 |
|---|---|
| LM4780TA | Audio Power Amplifier Series Stereo 60W, Mono 120W Audio Power Amplifier with Mute |
| LM4781TA | Overture⑩ Audio Power Amplifier Series 3 Channel 35W Audio Power Amplifier with Mute |
| LM4781 | Overture⑩ Audio Power Amplifier Series 3 Channel 35W Audio Power Amplifier with Mute |
| LM4782TA | 3 Channel 25W Audio Power Amplifier with Mute and Standby |
| LM4782 | 3 Channel 25W Audio Power Amplifier with Mute and Standby |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM4780TA | 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| LM4780TA | 制造商:Texas Instruments 功能描述:IC AMP 120W MONO/60W STEREO 4780 |
| LM4780TA/NOPB | 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| LM4780TABD | 功能描述:音頻 IC 開發工具 LM4780 EVAL BOARD RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| LM4780TABD/NOPB | 功能描述:BOARD EVAL FOR LM4780A RoHS:是 類別:編程器，開發系統 >> 評估板 - 音頻放大器 系列:Overture™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- |
發布緊急采購，3分鐘左右您將得到回復。