參數資料
型號： LM4121AIM5X-1.2
廠商： NATIONAL SEMICONDUCTOR CORP
元件分類： 基準電壓源/電流源
英文描述： Precision Micropower Low Dropout Voltage Reference
中文描述： 1-OUTPUT THREE TERM VOLTAGE REFERENCE, 1.25 V, PDSO5
封裝： SOT-23, 5 PIN
文件頁數： 13/16頁
文件大?。?/td> 436K
代理商： LM4121AIM5X-1.2
Pin Functions
Output (Pin 5):
Reference Output.
Input (Pin 4):
Positive Supply.
Ground (Pin 2):
Negative Supply or Ground Connection.
Enable (Pin 3):
Pulled to input for normal operation. Forcing
this pin to ground will turn-off the output.
REF (Pin 1):
REF Pin (1.25V option only). This pin should be
left unconnected for 1.25V option.
Adj (Pin 1):
V
Adj Pin (Adjustable option only). See Appli-
cation Hints section.
Application Hints
The standard application circuit for the LM4121 is shown in
Figure 1 The output voltage is set with the two feedback re-
sistors, according to the following formula:
V
OUT
= [V
ref
(1+ R1/R2] I
bias
R1
Values for R1 and R2 should be chosen to be less than 1
M
. I
bias
typically flows out of the adjust pin. Values for V
and I
are found in the Electrical Characteristics Spec.
table. For best accuracy, be sure to take into account the
variation of V
REF
with input voltage, load and output voltage.
The LM4121 is designed to be stable with ceramic output ca-
pacitors in the range of 0.022μF to 0.047μF. Note that
0.022μF is the minimum required output capacitor. These ca-
pacitors typically have an ESR of about 0.1 to 0.5
. Smaller
ESR can be tolerated, however larger ESR can not. The out-
put capacitor can be increased to improve load transient re-
sponse, up to about 1μF. However, values above 0.047μF
must be tantalum. With tantalum capacitors, in the 1μF
range, a small capacitor between the output and the refer-
ence (Adj) pin is required. This capacitor will typically be in
the 50pF range. Care must be taken when using output ca-
pacitors of 1μF or larger. These application must be thor-
oughly tested over temperature, line and load. Also, when
the LM4121 is used as a controller, with external active com-
ponents, each application must be carefully tested to ensure
a stable design. The adjust pin is sensitive to noise and ca-
pacitive loading. The trace to this pin must be as short as
possible and the feedback resistiors should be close to this
pin. Also, a single point ground to the LM4121 will help en-
sure good accuracy at high load currents.
An input capacitor is typically not required. However, a 0.1μF
ceramic can be used to help prevent line transients from en-
tering the LM4121. Larger input capacitors should be tanta-
lum or aluminium.
The enable pin is an analog input with very little hysteresis.
About 6μA into this pin is required to turn the part on, and it
must be taken close to GND to turn the part off (see spec.
table for thresholds). There is a minimum slew rate on this
pin of about 0.003V/μS to prevent glitches on the output. All
of these conditions can easily be met with ordinary CMOS or
TTL logic. If the shutdown feature is not required, then this
pin can safely be connected directly to the input supply.
Floating this pin is not recommended.
Printed Circuit Board Layout Consideration
The mechanical stress due to PC board mounting can cause
the output voltage to shift from its initial value. References in
SOT packages are generally less prone to assembly stress
than devices in Small Outline (SOIC) package.
To reduce the stress-related output voltage shifts, mount the
reference on the low flex areas of the PC board such as near
to the edge or the corner of the PC board.
DS101291-32
DS101291-43
FIGURE 1. Standard Application Circuit
L
www.national.com
13
相關PDF資料
PDF描述
LM4121 Precision Micropower Low Dropout Voltage Reference
LM4130AIM5X-4.1 Precision Micropower Low Dropout Voltage Reference
LM4130BIM5X-4.1 Precision Micropower Low Dropout Voltage Reference
LM4130CIM5X-4.1 Precision Micropower Low Dropout Voltage Reference
LM4130DIM5X-4.1 Precision Micropower Low Dropout Voltage Reference
相關代理商/技術參數
參數描述
LM4121AIM5X-ADJ 功能描述:基準電壓& 基準電流 RoHS:否 制造商:STMicroelectronics 產品:Voltage References 拓?fù)浣Y(jié)構:Shunt References 參考類型:Programmable 輸出電壓:1.24 V to 18 V 初始準確度:0.25 % 平均溫度系數（典型值）:100 PPM / C 串聯 VREF - 輸入電壓（最大值）: 串聯 VREF - 輸入電壓（最小值）: 分流電流（最大值）:60 mA 最大工作溫度:+ 125 C 封裝 / 箱體:SOT-23-3L 封裝:Reel
LM4121AIM5X-ADJ/NOPB 功能描述:基準電壓& 基準電流 RoHS:否 制造商:STMicroelectronics 產品:Voltage References 拓?fù)浣Y(jié)構:Shunt References 參考類型:Programmable 輸出電壓:1.24 V to 18 V 初始準確度:0.25 % 平均溫度系數（典型值）:100 PPM / C 串聯 VREF - 輸入電壓（最大值）: 串聯 VREF - 輸入電壓（最小值）: 分流電流（最大值）:60 mA 最大工作溫度:+ 125 C 封裝 / 箱體:SOT-23-3L 封裝:Reel
LM4121IM5-1.2 功能描述:基準電壓& 基準電流 RoHS:否 制造商:STMicroelectronics 產品:Voltage References 拓?fù)浣Y(jié)構:Shunt References 參考類型:Programmable 輸出電壓:1.24 V to 18 V 初始準確度:0.25 % 平均溫度系數（典型值）:100 PPM / C 串聯 VREF - 輸入電壓（最大值）: 串聯 VREF - 輸入電壓（最小值）: 分流電流（最大值）:60 mA 最大工作溫度:+ 125 C 封裝 / 箱體:SOT-23-3L 封裝:Reel
LM4121IM5-1.2/NOPB 功能描述:基準電壓& 基準電流 RoHS:否 制造商:STMicroelectronics 產品:Voltage References 拓?fù)浣Y(jié)構:Shunt References 參考類型:Programmable 輸出電壓:1.24 V to 18 V 初始準確度:0.25 % 平均溫度系數（典型值）:100 PPM / C 串聯 VREF - 輸入電壓（最大值）: 串聯 VREF - 輸入電壓（最小值）: 分流電流（最大值）:60 mA 最大工作溫度:+ 125 C 封裝 / 箱體:SOT-23-3L 封裝:Reel
LM4121IM5-ADJ 功能描述:基準電壓& 基準電流 RoHS:否 制造商:STMicroelectronics 產品:Voltage References 拓?fù)浣Y(jié)構:Shunt References 參考類型:Programmable 輸出電壓:1.24 V to 18 V 初始準確度:0.25 % 平均溫度系數（典型值）:100 PPM / C 串聯 VREF - 輸入電壓（最大值）: 串聯 VREF - 輸入電壓（最小值）: 分流電流（最大值）:60 mA 最大工作溫度:+ 125 C 封裝 / 箱體:SOT-23-3L 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*