- 您現在的位置：買賣IC網 > PDF目錄358846 > LM3543M-L (NATIONAL SEMICONDUCTOR CORP) Triple Port USB Power Distribution Switch and Over-Current Protection PDF資料下載
參數資料
| 型號： | LM3543M-L |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 電源管理 |
| 英文描述： | Triple Port USB Power Distribution Switch and Over-Current Protection |
| 中文描述： | 3-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16 |
| 封裝： | SOIC-16 |
| 文件頁數： | 9/12頁 |
| 文件大小： | 316K |
| 代理商： | LM3543M-L |
Functional Description
(Continued)
In Figure 3 port 1 is enabled into a short. When this occurs,
the MOSFET switch of port 1 repeatedly opens and closes
as the device temperature rises and falls between 145C and
135C. In this example, the device temperature never rises
above 160C. The second stage thermal shutdown is not
used and port 2 remains operational.
When port 1 is enabled into a short in the example illustrated
in Figure 4 the device temperature immediately rises above
160C. A higher ambient temperature or a larger number of
shorted outputs can cause the junction temperature to
increase, resulting in the difference in behavior between the
current example and the previous one. When the junction
temperature reaches 160C, all three ports are disabled (port
3 is not shown in the figure) and all three fault-flag signals
are asserted. Just prior to time index 2.5 ms, the device
temperature falls below 135C, all three ports activate, and
all three fault flags are removed. The short condition remains
on port 1, however. For the remainder of the example, the
device temperature cycles between 135C and 145C,
causing port 1 to repeatedly turn on and off but allowing the
un-shorted ports to function normally.
Soft Start
When a power switch is enabled, high levels of current will
flow instantaneously through the LM3543 to charge the large
capacitance at the output of the port. This is likely to exceed
the over-current threshold of the device, at which point the
LM3543 will enter its current-limit mode. The amount of
current used to charge the output capacitor is then set by the
current-limit circuitry. The device will exit the current-limit
mode when the current needed to continue to charge the
output capacitor is less than the LM3543 current-limit level.
Fault Flag
The fault flags are open-drain outputs, each capable of
sinking up to a 10 mA load current to typically 100 mV above
ground.
A parasitic diode exists between the flag pins and V
pins.
Pulling the flag pins to voltages higher than V
will forward
bias this diode and will cause an increase in supply current.
This diode will also clamp the voltage on the flag pins to a
diode drop above V
IN
.
The fault flag is active (pulled low) when any of the following
conditions are present: under-voltage, current-limit, or
thermal-shutdown.
The LM3543 has an internal delay in reporting fault
conditions that is typically 7 ms in length. In start-up, the
delay gives the device time to charge the output capacitor(s)
and exit the current-limit mode before a flag signal is set.
This delay also prevents flag signal glitches from occurring
when brief changes in operating conditions momentarily
place the LM3543 into one of its three error conditions. If an
error condition still exists after the delay interval has
elapsed, the appropriate fault flag(s) will be asserted (pulled
low)
until
the
error
condition
applications, the 7 ms internal flag delay eliminates the need
to extend the delay with an external RC delay network.
is
removed.
In
most
Application Information
Output Filtering
The schematic in Figure 1 showed a typical application
circuit for the LM3543. The USB specification requires 120
μF at the output of each hub. A three-port hub with 33 μF
tantalum
capacitors
at
each
specification. These capacitors provide short-term transient
current to drive downstream devices when hot-plug events
occur. Capacitors with low equivalent-series-resistance
should be used to lower the inrush current flow through the
LM3543 during a hot-plug event.
The rapid change in currents seen during a hot plug event
can generate electromagnetic interference (EMI). To reduce
this effect, ferrite beads in series between the outputs of the
LM3543 and the downstream USB port are recommended.
Beads should also be placed between the ground node of
the
LM3543
and
the
ground
downstream ports. In order to keep voltage drop across the
beads to a minimum, wire with small DC resistance should
be used through the ferrite beads.A0.01 μF - 0.1 μF ceramic
capacitor is recommended on each downstream port directly
between the V
bus
and ground pins to further reduce EMI
effects.
port
output
meets
the
nodes
of
connected
Power Supply Filtering
A sizable capacitor should be connected to the input of the
LM3543 to ensure the voltage drop on this node is less than
330 mV during a heavy-load hot-plug event. A 33 μF, 16V
10125825
FIGURE 3. Thermal Shutdown Characteristics when
only the First-Stage Thermal-Shutdown Mode is
Needed
10125826
FIGURE 4. Thermal Shutdown Characteristics when
Both First-Stage and Second-Stage Thermal-Shutdown
Modes are Needed
L
www.national.com
9
相關PDF資料 |
PDF描述 |
|---|---|
| LM3543M-H | Triple Port USB Power Distribution Switch and Over-Current Protection |
| LM3543MX-L | Triple Port USB Power Distribution Switch and Over-Current Protection |
| LM3543 | Triple Port USB Power Distribution Switch and Over-Current Protection |
| LM3544M-H | Quad Port USB Power Distribution Switch and Over-Current Protection |
| LM3544M-L | Backplane/Data Transfer Connector; No. of Contacts:50; No. of Rows:2; Mounting Type:PCB Straight Thru Hole; Contact Plating:Gold; Current Rating:2A; Gender:Female; Leaded Process Compatible:Yes RoHS Compliant: Yes |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM3543MX-H | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Triple Port USB Power Distribution Switch and Over-Current Protection |
| LM3543MX-H/NOPB | 功能描述:IC PWR SWITCH TRPL HISIDE 16SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 電源分配開關 系列:- 特色產品:XRP252 Switches 標準包裝:1 系列:- 類型:高端開關 輸出數:2 Rds（開）:140 毫歐 內部開關:是 電流限制:1.15A 輸入電壓:1.75 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN（3x3） 包裝:Digi-Reel® 其它名稱:1016-1691-6 |
| LM3543MX-L | 制造商:Rochester Electronics LLC 功能描述: 制造商:Texas Instruments 功能描述: |
| LM3543MX-L/NOPB | 制造商:Texas Instruments 功能描述:USB Power SW Hi Side/DIST Triple 5.5V 2A 16-Pin SOIC N T/R |
| LM3544 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Quad Port USB Power Distribution Switch and Over-Current Protection |
發布緊急采購，3分鐘左右您將得到回復。