- 您現在的位置：買賣IC網 > PDF目錄385480 > LM29 (National Semiconductor Corporation) LM2900/LM3900/LM3301 Quad Amplifiers PDF資料下載
參數資料
| 型號： | LM29 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | LM2900/LM3900/LM3301 Quad Amplifiers |
| 中文描述： | LM2900/LM3900/LM3301四放大器 |
| 文件頁數： | 3/20頁 |
| 文件大?。?/td> | 338K |
| 代理商： | LM29 |
Electrical Characteristics
(Note 6), V
a
e
15 V
DC
, unless otherwise stated (Continued)
Parameter
Conditions
LM2900
LM3900
LM3301
Units
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Power Supply Rejection
T
A
e
25
§
C, f
e
100 Hz
70
70
70
dB
Mirror Gain
@
20
m
A (Note 3)
@
200
m
A (Note 3)
0.90
0.90
1.0
1.0
1.1
1.1
0.90
0.90
1.0
1.0
1.1
1.1
0.90
0.90
1
1
1.10
1.10
m
A/
m
A
D
Mirror Gain
@
20
m
A to 200
m
A (Note 3)
2
5
2
5
2
5
%
Mirror Current
(Note 4)
10
500
10
500
10
500
m
A
DC
Negative Input Current
T
A
e
25
§
C (Note 5)
1.0
1.0
1.0
mA
DC
Input Bias Current
Inverting Input
300
300
nA
Note 1:
For operating at high temperatures, the device must be derated based on a 125
§
C maximum junction temperature and a thermal resistance of 92
§
C/W
which applies for the device soldered in a printed circuit board, operating in a still air ambient. Thermal resistance for the S.O. package is 131
§
C/W.
Note 2:
The output current sink capability can be increased for large signal conditions by overdriving the inverting input. This is shown in the section on Typical
Characteristics.
Note 3:
This spec indicates the current gain of the current mirror which is used as the non-inverting input.
Note 4:
Input V
BE
match between the non-inverting and the inverting inputs occurs for a mirror current (non-inverting input current) of approximately 10
m
A. This is
therefore a typical design center for many of the application circuits.
Note 5:
Clamp transistors are included on the IC to prevent the input voltages from swinging below ground more than approximately
b
0.3 V
DC
. The negative input
currents which may result from large signal overdrive with capacitance input coupling need to be externally limited to values of approximately 1 mA. Negative input
currents in excess of 4 mA will cause the output voltage to drop to a low voltage. This maximum current applies to any one of the input terminals. If more than one
of the input terminals are simultaneously driven negative smaller maximum currents are allowed. Common-mode current biasing can be used to prevent negative
input voltages; see for example, the ‘‘Differentiator Circuit’’ in the applications section.
Note 6:
These specs apply for
b
40
§
C
s
T
A
s
a
85
§
C, unless otherwise stated.
Note 7:
Human body model, 1.5 k
X
in series with 100 pF.
Application Hints
When driving either input from a low-impedance source, a
limiting resistor should be placed in series with the input
lead to limit the peak input current. Currents as large as
20 mA will not damage the device, but the current mirror on
the non-inverting input will saturate and cause a loss of mir-
ror gain at mA current levelsDespecially at high operating
temperatures.
Precautions should be taken to insure that the power supply
for the integrated circuit never becomes reversed in polarity
or that the unit is not inadvertently installed backwards in a
test socket as an unlimited current surge through the result-
ing forward diode within the IC could cause fusing of the
internal conductors and result in a destroyed unit.
Output short circuits either to ground or to the positive pow-
er supply should be of short time duration. Units can be
destroyed, not as a result of the short circuit current causing
metal fusing, but rather due to the large increase in IC chip
dissipation which will cause eventual failure due to exces-
sive junction temperatures. For example, when operating
from a well-regulated
a
5 V
DC
power supply at T
A
e
25
§
C
with a 100 k
X
shunt-feedback resistor (from the output to
the inverting input) a short directly to the power supply will
not cause catastrophic failure but the current magnitude will
be approximately 50 mA and the junction temperature will
be above T
J
max. Larger feedback resistors will reduce the
current, 11 M
X
provides approximately 30 mA, an open cir-
cuit provides 1.3 mA, and a direct connection from the out-
put to the non-inverting input will result in catastrophic fail-
ure when the output is shorted to V
as this then places the
base-emitter junction of the input transistor directly across
the power supply. Short-circuits to ground will have magni-
tudes of approximately 30 mA and will not cause cata-
strophic failure at T
A
e
25
§
C.
Unintentional signal coupling from the output to the non-in-
verting input can cause oscillations. This is likely only in
breadboard hook-ups with long component leads and can
be prevented by a more careful lead dress or by locating the
non-inverting input biasing resistor close to the IC. A quick
check of this condition is to bypass the non-inverting input
to ground with a capacitor. High impedance biasing resis-
tors used in the non-inverting input circuit make this input
lead highly susceptible to unintentional AC signal pickup.
Operation of this amplifier can be best understood by notic-
ing that input currents are differenced at the inverting-input
terminal and this difference current then flows through the
external feedback resistor to produce the output voltage.
Common-mode current biasing is generally useful to allow
operating with signal levels near ground or even negative as
this maintains the inputs biased at
a
V
BE
. Internal clamp
transistors (see note 5) catch-negative input voltages at ap-
proximately
b
0.3 V
DC
but the magnitude of current flow has
to be limited by the external input network. For operation at
high temperature, this limit should be approximately 100
m
A.
This new ‘‘Norton’’ current-differencing amplifier can be
used in most of the applications of a standard IC op amp.
Performance as a DC amplifier using only a single supply is
not as precise as a standard IC op amp operating with split
supplies but is adequate in many less critical applications.
New functions are made possible with this amplifier which
are useful in single power supply systems. For example,
biasing can be designed separately from the AC gain as was
shown in the ‘‘inverting amplifier,’’ the ‘‘difference integra-
tor’’ allows controlling the charging and the discharging of
the integrating capacitor with positive voltages, and the ‘‘fre-
quency doubling tachometer’’ provides a simple circuit
which reduces the ripple voltage on a tachometer output DC
voltage.
3
相關PDF資料 |
PDF描述 |
|---|---|
| LM309KSTEEL | 5-Volt Regulator |
| LM3100 | SIMPLE SWITCHER㈢ Synchronous 1MHz 1.5A Step-Down Voltage Regulator |
| LM3100MH | SIMPLE SWITCHER㈢ Synchronous 1MHz 1.5A Step-Down Voltage Regulator |
| LM3100MHX | SIMPLE SWITCHER㈢ Synchronous 1MHz 1.5A Step-Down Voltage Regulator |
| LM3189 | LM3189 FM IF System |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM290 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Low power dual operational amplifi |
| LM2900 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:QUAD SINGLE SUPPLY OPERATIONAL AMPLIFIERS |
| LM2900D | 功能描述:運算放大器 - 運放 Quadruple Oper Amplifier RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| LM2900DE4 | 功能描述:運算放大器 - 運放 Quadruple Oper Amplifier RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| LM2900DG4 | 功能描述:運算放大器 - 運放 Quad Op Amp RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。