- 您現在的位置：買賣IC網 > PDF目錄358829 > LM2825N-5.0 (NATIONAL SEMICONDUCTOR CORP) Integrated Power Supply 1A DC-DC Converter PDF資料下載
參數資料
| 型號： | LM2825N-5.0 |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Integrated Power Supply 1A DC-DC Converter |
| 中文描述： | 1.2 A SWITCHING REGULATOR, 150 kHz SWITCHING FREQ-MAX, PDIP24 |
| 封裝： | 1.250 X 0.540 INCH, 0.260 INCH HEIGHT, PLASTIC, DIP-24 |
| 文件頁數： | 8/12頁 |
| 文件大小： | 633K |
| 代理商： | LM2825N-5.0 |
Application Information
(Continued)
It is especially useful in situations where the input power
source is limited in the amount of current it can deliver, since
you avoid loading down this type of power supply.
Under some operating conditions, a Soft-start capacitor is
required for proper operation. Figure 5 indicates the input
voltage and ambient temperature conditions for which a
Soft-start capacitor may be required.
This curve is typical for full guaranteed output current and
can be used as a guideline.As the output current decreases,
the operating area requiring a Soft-start capacitor de-
creases. Capacitor values between 0.1 μF and 1 μF are rec-
ommended. Tantalum or ceramic capacitors are appropriate
for this application.
INPUT CAPACITOR
C
:
An optional input capacitor is required if the package is
more than 6" away from the main filter or bypass capacitor.A
low ESR aluminum or tantalum bypass capacitor is recom-
mended between the input pin and ground to prevent large
voltage transients from appearing at the input. In addition, to
be conservative, the RMS current rating of the input capaci-
tor should be selected to be at least
1
2
the DC load current.
With a 1A load, a capacitor with a RMS current rating of at
least 500 mA is recommended.
The voltage rating should be approximately 1.25 times the
maximum input voltage. With a nominal input voltage of 12V,
an aluminum electrolytic capacitor (Panasonic HFQ series or
Nichicon PL series or equivalent) with a voltage rating
greater than 15V (1.25 x V
IN
) would be needed.
Solid tantalum input capacitors should only be used where
the input source is impedance current limited. High dV/dt ap-
plied at the input can cause excessive charge current
through low ESR tantalum capacitors. This high charge cur-
rent can result in shorting within the capacitor. It is recom-
mended that they be surge current tested by the manufactur-
er.The TPS series available from AVX, and the 593D series
from Sprague are both surge current tested.
Use caution when using ceramic capacitors for input bypass-
ing, because it may cause ringing at the V
IN
pin.
LOWERING OUTPUT RIPPLE
When using the adjustable parts, one can achieve lower out-
put ripple voltage by shorting a resistor internal to the
LM2825. However, if this resistor is shorted, a feed forward
capacitor must be used to keep the regulator stable. For this
reason, this resistor must be left open on all of the fixed out-
put voltage versions or instability will result. See the feed for-
ward capacitor selection below. Shorting the internal resistor
is accomplished by shorting pins 8 and 9 on the LM2825,
and will typically reduce output ripple by 25 to 33%.
FEED FORWARD CAPACITOR SELECTION (C
FF
)
When using an adjustable part and pins 8 and 9 are shorted
to reduce output ripple, a feed forward capacitor is required.
This capacitor is typically between 680 pF and 2700 pF. The
table of Figure 4 shows the value for C
for a given output
voltage and feedback resistor R
2
(R1 = 1 k
).
SHUTDOWN
The circuit shown in Figure 10 shows 2 circuits for the
Shutdown/Soft-start feature using different logic signals for
shutdown and using a 0.1 μF Soft-start capacitor.
THERMAL CONSIDERATIONS
The LM2825 is available in a 24-pin through hole DIP. The
package is molded plastic with a copper lead frame. When
the package is soldered to the PC board, the copper and the
board are the heat sink for the LM2825.
V
OUT
R2
C
FF
LM2825-ADJ
630
1.43k
2.26k
3.09k
3.92k
4.75k
5.49k
LM2825H-ADJ
4.75k
5.49k
6.34k
7.15k
8.06k
8.87k
9.53k
10.5k
11.3k
2
3
4
5
6
7
8
N/A
N/A
2700 pF
2700 pF
2200 pF
1800 pF
1500 pF
7
8
9
2700 pF
2200 pF
1800 pF
1500 pF
1000 pF
820 pF
680 pF
680 pF
680 pF
10
11
12
13
14
15
FIGURE 4. C
FF
Selection Table
DS012661-22
FIGURE 5. Usage of the Soft-start Capacitor
www.national.com
8
相關PDF資料 |
PDF描述 |
|---|---|
| LM2825N-ADJ | Integrated Power Supply 1A DC-DC Converter |
| LM2825HN-ADJ | Integrated Power Supply 1A DC-DC Converter |
| LM2825-12 | Integrated Power Supply 1A DC-DC Converter(633.82 k) |
| LM2825-3.3 | Integrated Power Supply 1A DC-DC Converter(633.82 k) |
| LM2825-5.0 | Integrated Power Supply 1A DC-DC Converter(633.82 k) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM2825N50 | 制造商:Texas Instruments 功能描述:SWITCHING REG 1A 5.0V 2825 DIP24 |
| LM2825N-ADJ | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| LM2825N-ADJ | 制造商:Texas Instruments 功能描述:SWITCHING REG 1A ADJ 2825 DIP24 |
| LM2825N-ADJ/NOPB | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| LM2826 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Low Dropout Regulator with Delayed Reset |
發布緊急采購，3分鐘左右您將得到回復。