參數資料
型號: LM2788MM-1.8
廠商: NATIONAL SEMICONDUCTOR CORP
元件分類: 穩壓器
英文描述: 120mA High Efficiency Step-Down Switched Capacitor Voltage Converter
中文描述: SWITCHED CAPACITOR REGULATOR, 500 kHz SWITCHING FREQ-MAX, PDSO8
封裝: MSOP-8
文件頁數: 10/12頁
文件大?。?/td> 372K
代理商: LM2788MM-1.8
Application Information
(Continued)
low-ESR ceramic capacitor is recommended on the output to
keep output voltage ripple low. Placing multiple capacitors in
parallel can reduce ripple significantly, both by increasing
capacitance and reducing ESR. When capacitors are in
parallel, ESR is in parallel as well. The effective net ESR is
determined according to the properties of parallel resistance.
Two identical capacitors in parallel have twice the capaci-
tance and half the ESR as compared to a single capacitor of
the same make. On a similar note, if a large-value, high-ESR
capacitor (tantalum, for example) is to be used as the pri-
mary output capacitor, the net output ESR can be signifi-
cantly reduced by placing a low-ESR ceramic capacitor in
parallel with this primary output capacitor.
Ripple is increased when the LM2788 is gain hopping. Thus,
in the presence of high currents, ripple is likely to vary
significantly over the input voltage, depending on wether or
not the part is gain hopping.
CAPACITORS
The LM2788 requires 4 external capacitors for proper opera-
tion. Surface-mount multi-layer ceramic capacitors are rec-
ommended. These capacitors are small, inexpensive and
have very low equivalent series resistance (ESR,
15m
typ.). Tantalum capacitors, OS-CON capacitors, and alumi-
num electrolytic capacitors generally are not recommended
for use with the LM2788 due to their high ESR, as compared
to ceramic capacitors.
For most applications, ceramic capacitors with X7R or X5R
temperature characteristic are preferred for use with the
LM2788. These capacitors have tight capacitance tolerance
(as good as
±
10%), hold their value over temperature (X7R:
±
15% over -55
o
C to 125
o
C; X5R:
±
15% over -55
o
C to 85
o
C),
and typically have little voltage coefficient.
Capacitors with Y5V and/or Z5U temperature characteristic
are generally not recommended for use with the LM2788.
These types of capacitors typically have wide capacitance
tolerance (+80%, -20%), vary significantly over temperature
(Y5V: +22%, -82% over -30
o
C to +85
o
C range; Z5U: +22%,
-56% over +10
o
C to +85
o
C range), and have poor voltage
coefficients. Under some conditions, a nominal 1μF Y5V or
Z5U capacitor could have a capacitance of only 0.1μF. Such
detrimental deviation is likely to cause these Y5V and Z5U of
capacitors to fail to meet the minimum capacitance require-
ments of the LM2788.
The table below lists some leading ceramic capacitor manu-
facturers.
Manufacturer
AVX
Murata
Taiyo-Yuden
TDK
Vishay-Vitramon
Contact Information
www.avx.com
www.murata.com
www.t-yuden.com
www.component.tdk.com
www.vishay.com
OUTPUT CAPACITOR
The output capacitor of the LM2788 plays an important part
in LM2788 performance. In typical high-current applications,
a 10μF low-ESR (ESR = equivalent series resistance) ce-
ramic capacitor is recommended for use. For lighter loads,
the output capacitance may be reduced (capacitance as low
as 1μF for output currents
60mA is usually acceptable).
The performance of the part should be evaluated with spe-
cial attention paid to efficiency and output ripple to ensure
the capacitance chosen on the output yields performance
suitable for the application. In extreme cases, excessive
ripple could cause control loop instability, severely affecting
the performance of the part. If excessive ripple is present,
the output capacitance should be increased.
The ESR of the output capacitor affects charge pump output
resistance, which plays a role in determining output current
capability. Both output capacitance and ESR affect output
voltage ripple (See Output Voltage Ripple section, above).
For these reasons, a low-ESR X7R/X5R ceramic capacitor is
the capacitor of choice for the LM2788 output.
FLYING CAPACITORS
The flying capacitors (C
and C
) transfer charge from the
input to the output, and thus are like the engine of the charge
pump. Low-ESR ceramic capacitors with X7R or X5R tem-
perature characteristic are strongly recommended for use
here. The flying capacitors C1 and C2 should be identical.As
a general rule, the capacitance value of each flying capacitor
should be 1/10th that of the output capacitor. Polarized
capacitor (tantalum, aluminum electrolytic, etc.) must not be
used for the flying capacitors, as they could become reverse-
biased upon start-up of the LM2788.
The flying capacitance determines the strength of the charge
pump-the larger the capacitance, the bigger the engine. ESR
in the flying capacitors negatively affects the strength of the
charge pump and should be minimized, as ESR contributes
to undesired output resistance. If capacitors are too small
the LM2788 could spend excessive amount of time gain
hopping: decreasing efficiency, increasing output voltage
ripple, and possibly impeding the ability of the part to regu-
late. On the other hand, if the flying capacitors are too large
they could potentially overwhelm the output capacitor, result-
ing in increased output voltage ripple.
INPUT CAPACITOR
If the flying capacitors are the charge pump engine, the input
capacitor (CIN) is the fuel tank: a reservoir of charge that
aids a quick transfer of charge from the supply to the flying
capacitors during the charge phase of operation. The input
capacitor helps to keep the input voltage from drooping at
the start of the charge phase, when the flying capacitor is
first connected to the input, and helps to filter noise on the
input pin that could adversely affect sensitive internal analog
circuitry biased off the input line. As mentioned above, an
X7R/X5R ceramic capacitor is recommended for use. As a
general recommendation, the input capacitor should be cho-
sen to match the output capacitor.
POWER DISSIPATION
LM2788 power dissipation will, typically, not be much of a
concern in most applications. Derating to accommodate self-
heating will rarely be required due to the high efficiency of
the part. When operating within specified operating ratings,
the peak power dissipation (PD) of all LM2788 voltage op-
tions occurs with the LM2788-1.5 operating at the maximum
rated operating output current of 120mA. With an input volt-
age of 5.5V, the power efficiency (E) of the LM2788-1.5
bottoms out at 54%. Assuming a typical junction-to-ambient
thermal resistance (
θ
JA) for the MSOP package of 220C/
Watt, the junction temperature (T
J
) of the part is calculated
below for a part operating at the maximum rated ambient
temperature (T
A
) of 85C.
L
www.national.com
10
相關PDF資料
PDF描述
LM2788MMX-1.8 120mA High Efficiency Step-Down Switched Capacitor Voltage Converter
LM2788 120mA High Efficiency Step-Down Switched Capacitor Voltage Converter
LM2793LDX Low Noise White LED Constant Current Supply with Dual Function Brightness Control
LM2793LD Low Noise White LED Constant Current Supply with Dual Function Brightness Control
LM2793 Low Noise White LED Constant Current Supply with Dual Function Brightness Control
相關代理商/技術參數
參數描述
LM2788MM-2.0 制造商:Rochester Electronics LLC 功能描述:120MA STEP DOWN BUCK CONVERTER - Bulk
LM2788MM-2.0/NOPB 功能描述:IC REG BUCK SWITCHD CAP 2V 8MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:降壓(降壓) 輸出類型:固定 輸出數:1 輸出電壓:3.3V 輸入電壓:4.5 V ~ 24 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:125mA 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 包裝:Digi-Reel® 供應商設備封裝:SOT-6 其它名稱:MAX1836EUT33#TG16DKR
LM2788MMX-1.5 制造商:NSC 制造商全稱:National Semiconductor 功能描述:120mA High Efficiency Step-Down Switched Capacitor Voltage Converter
LM2788MMX-1.8 制造商:NSC 制造商全稱:National Semiconductor 功能描述:120mA High Efficiency Step-Down Switched Capacitor Voltage Converter
LM2788MMX-2.0 制造商:NSC 制造商全稱:National Semiconductor 功能描述:120mA High Efficiency Step-Down Switched Capacitor Voltage Converter