- 您現在的位置：買賣IC網 > PDF目錄358827 > LM2700 (National Semiconductor Corporation) 600kHz/1.25MHz, 2.5A, Step-up PWM DC/DC Converter PDF資料下載
參數資料
| 型號： | LM2700 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | 600kHz/1.25MHz, 2.5A, Step-up PWM DC/DC Converter |
| 中文描述： | 600kHz/1.25MHz，包2.5a，升壓PWM型DC / DC轉換器 |
| 文件頁數： | 11/17頁 |
| 文件大小： | 478K |
| 代理商： | LM2700 |
Operation
(Continued)
The phase margin can also be improved by adding C
C2
as
discussed earlier in the section. The equation for A
is
given below with additional equations required for the calcu-
lation:
mc
)
0.072fs (in V/s)
where R
is the minimum load resistance, V
is the maxi-
mum input voltage, g
is the error amplifier transconduc-
tance found in the Electrical Characteristics table, and R
D-
SON
is the value chosen from the graph ’R
vs. V
IN
’ in
the Typical Performance Characteristics section.
Application Information
Layout Considerations
The LM2700 uses two separate ground connections, PGND
for the driver and NMOS power device and AGND for the
sensitive analog control circuitry. The AGND and PGND pins
should be tied directly together at the package. The feed-
back and compensation networks should be connected di-
rectly to a dedicated analog ground plane and this ground
plane must connect to the AGND pin. If no analog ground
plane is available then the ground connections of the feed-
back and compensation networks must tie directly to the
AGND pin. Connecting these networks to the PGND can
inject noise into the system and effect performance.
The input bypass capacitor C
, as shown in Figure 3 must
be placed close to the IC. This will reduce copper trace
resistance which effects input voltage ripple of the IC. For
additional input voltage filtering, a 100nF bypass capacitor
can be placed in parallel with C
, close to the V
pin, to
shunt any high frequency noise to ground. The output ca-
pacitor, C
, should also be placed close to the IC. Any
copper trace connections for the C
capacitor can in-
crease the series resistance, which directly effects output
voltage ripple. The feedback network, resistors R
and
R
, should be kept close to the FB pin, and away from the
inductor, to minimize copper trace connections that can in-
ject noise into the system. Trace connections made to the
inductor and schottky diode should be minimized to reduce
power dissipation and increase overall efficiency. For more
detail on switching power supply layout considerations see
Application Note AN-1149: Layout Guidelines for Switching
Power Supplies
20012331
FIGURE 3. 600 kHz operation, 8V output
L
www.national.com
11
相關PDF資料 |
PDF描述 |
|---|---|
| LM2703MF-ADJ | Micropower Step-up DC/DC Converter with 350mA Peak Current Limit |
| LM2703MFX-ADJ | Micropower Step-up DC/DC Converter with 350mA Peak Current Limit |
| LM2703 | Micropower Step-up DC/DC Converter with 350mA Peak Current Limit |
| LM2704MF-ADJ | Micropower Step-up DC/DC Converter with 550mA Peak Current Limit |
| LM2704MFX-ADJ | Micropower Step-up DC/DC Converter with 550mA Peak Current Limit |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM2700_04 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:600kHz/1.25MHz, 2.5A, Step-up PWM DC/DC Converter |
| LM2700LD-ADJ | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| LM2700LD-ADJ/NOPB | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| LM2700LDX-ADJ | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:600kHz/1.25MHz, 2.5A, Step-up PWM DC/DC Converter |
| LM2700LDX-ADJ/NOPB | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
發布緊急采購，3分鐘左右您將得到回復。