- 您現在的位置：買賣IC網 > PDF目錄358826 > LM2676S-3.3 (NATIONAL SEMICONDUCTOR CORP) SIMPLE SWITCHER High Efficiency 3A Step-Down Voltage Regulator PDF資料下載
參數資料
| 型號： | LM2676S-3.3 |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | SIMPLE SWITCHER High Efficiency 3A Step-Down Voltage Regulator |
| 中文描述： | 5.4 A SWITCHING REGULATOR, 280 kHz SWITCHING FREQ-MAX, PSSO7 |
| 封裝： | TO-263, 7 PIN |
| 文件頁數： | 10/25頁 |
| 文件大?。?/td> | 455K |
| 代理商： | LM2676S-3.3 |
Application Hints
The LM2676 provides all of the active functions required for
a step-down (buck) switching regulator. The internal power
switch is a DMOS power MOSFET to provide power supply
designs with high current capability, up to 3A, and highly
efficient operation.
The LM2676 is part of the
SIMPLE SWITCHER
family of
power converters. A complete design uses a minimum num-
ber of external components, which have been pre-
determined from a variety of manufacturers. Using either this
data sheet or a design software program called
LM267X
Made Simple
(version 2.0) a complete switching power
supply can be designed quickly. The software is provided
free of charge and can be downloaded from National Semi-
conductor’s Internet site located at http://www.national.com.
SWITCH OUTPUT
This is the output of a power MOSFET switch connected
directly to the input voltage. The switch provides energy to
an inductor, an output capacitor and the load circuitry under
control of an internal pulse-width-modulator (PWM). The
PWM controller is internally clocked by a fixed 260KHz
oscillator. In a standard step-down application the duty cycle
(Time ON/Time OFF) of the power switch is proportional to
the ratio of the power supply output voltage to the input
voltage. The voltage on pin 1 switches between Vin (switch
ON) and below ground by the voltage drop of the external
Schottky diode (switch OFF).
INPUT
The input voltage for the power supply is connected to pin 2.
In addition to providing energy to the load the input voltage
also provides bias for the internal circuitry of the LM2676.
For guaranteed performance the input voltage must be in the
range of 8V to 40V. For best performance of the power
supply the input pin should always be bypassed with an input
capacitor located close to pin 2.
C BOOST
A capacitor must be connected from pin 3 to the switch
output, pin 1. This capacitor boosts the gate drive to the
internal MOSFET above Vin to fully turn it ON. This mini-
mizes conduction losses in the power switch to maintain high
efficiency. The recommended value for C Boost is 0.01μF.
GROUND
This is the ground reference connection for all components
in the power supply. In fast-switching, high-current applica-
tions such as those implemented with the LM2676, it is
recommended that a broad ground plane be used to mini-
mize signal coupling throughout the circuit
FEEDBACK
This is the input to a two-stage high gain amplifier, which
drives the PWM controller. It is necessary to connect pin 6 to
the actual output of the power supply to set the dc output
voltage. For the fixed output devices (3.3V, 5V and 12V
outputs), a direct wire connection to the output is all that is
required as internal gain setting resistors are provided inside
the LM2676. For the adjustable output version two external
resistors are required to set the dc output voltage. For stable
operation of the power supply it is important to prevent
coupling of any inductor flux to the feedback input.
ON/OFF
This input provides an electrical ON/OFF control of the
power supply. Connecting this pin to ground or to any volt-
age less than 0.8V will completely turn OFF the regulator.
The current drain from the input supply when OFF is only
50μA. Pin 7 has an internal pull-up current source of approxi-
mately 20μA and a protection clamp zener diode of 7V to
ground. When electrically driving the ON/OFF pin the high
voltage level for the ON condition should not exceed the 6V
absolute maximum limit. When ON/OFF control is not re-
quired pin 7 should be left open circuited.
DAP (LLP PACKAGE)
The Die Attach Pad (DAP) can and should be connected to
PCB Ground plane/island. For CAD and assembly guide-
lines
refer
to
Application
power.national.com.
Note
AN-1187
at
http://
L
www.national.com
10
相關PDF資料 |
PDF描述 |
|---|---|
| LM2676T-12 | SIMPLE SWITCHER High Efficiency 3A Step-Down Voltage Regulator |
| LM2676T-3.3 | SIMPLE SWITCHER High Efficiency 3A Step-Down Voltage Regulator |
| LM2676S-5.0 | SIMPLE SWITCHER High Efficiency 3A Step-Down Voltage Regulator |
| LM2676S-ADJ | SIMPLE SWITCHER High Efficiency 3A Step-Down Voltage Regulator |
| LM2676T-5.0 | Hermetically sealed high temperature limit switch with Screw termination, Plunger actuation, Double Pole Double Throw (DPDT) Circuitry, 5 A (Resistive) ampere rating at 28 Vdc, Military Part Number MS24594-1 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM2676S-5 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:LM2676 SIMPLE SWITCHER High Efficiency 3A Step-Down Voltage Regulator |
| LM2676S-5.0 | 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| LM2676S-5.0/NOPB | 功能描述:直流/直流開關轉換器 HIGH EFF 3A STEP- DOWN VLTG REG RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| LM2676S-5.0/NOPB | 制造商:Texas Instruments 功能描述:DC/DC Converter (DC-DC) / Switching Regu |
| LM2676S-5.0EP | 制造商:TI 制造商全稱:Texas Instruments 功能描述:LM2676EP Enhanced Plastic SIMPLE SWITCHER High Efficiency 3A Step-Down Voltage Regulator |
發布緊急采購，3分鐘左右您將得到回復。