- 您現在的位置：買賣IC網 > PDF目錄369785 > LM2598-ADJ SIMPLE SWITCHER Power Converter 150 kHz 1A Step-Down Voltage Regulator with Features(572.00 k) PDF資料下載
參數資料
| 型號： | LM2598-ADJ |
| 英文描述： | SIMPLE SWITCHER Power Converter 150 kHz 1A Step-Down Voltage Regulator with Features(572.00 k) |
| 中文描述： | SIMPLE SWITCHER系列電源轉換器150千赫1A步降穩(wěn)壓器的功能（572.00十一） |
| 文件頁數： | 14/28頁 |
| 文件大?。?/td> | 739K |
| 代理商： | LM2598-ADJ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
LM2594/LM2594HV Series Buck Regulator Design Procedure (Adjustable
Output)
(Continued)
PROCEDURE (Adjustable Output Voltage Version)
EXAMPLE (Adjustable Output Voltage Version)
6. Input Capacitor (C
IN
)
Alow ESR aluminum or tantalum bypass capacitor is needed
between the input pin and ground to prevent large voltage
transients from appearing at the input. In addition, the RMS
current rating of the input capacitor should be selected to be
at least
1
2
the DC load current. The capacitor manufacturers
data sheet must be checked to assure that this current rating
is not exceeded. The curve shown in Figure 13shows typical
RMS current ratings for several different aluminum electro-
lytic capacitor values.
This capacitor should be located close to the IC using short
leads and the voltage rating should be approximately 1.5
times the maximum input voltage.
If solid tantalum input capacitors are used, it is recomended
that they be surge current tested by the manufacturer.
Use caution when using ceramic capacitors for input bypass-
ing, because it may cause severe ringing at the V
IN
pin.
For additional information, see section on input capaci-
tors in application information section.
6. Input Capacitor (C
IN
)
The important parameters for the Input capacitor are the in-
put voltage rating and the RMS current rating. With a nominal
input voltage of 28V, an aluminum electrolytic aluminum elec-
trolytic capacitor with a voltage rating greater than 42V (1.5 x
V
) would be needed. Since the the next higher capacitor
voltage rating is 50V, a 50V capacitor should be used. The
capacitor voltage rating of (1.5 x V
) is a conservative guide-
line, and can be modified somewhat if desired.
The RMS current rating requirement for the input capacitor of
a buck regulator is approximately
1
2
the DC load current. In
this example, with a 400 mA load, a capacitor with a RMS
current rating of at least 200 mA is needed.
The curves shown in Figure 13 can be used to select an ap-
propriate input capacitor. From the curves, locate the 50V
line and note which capacitor values have RMS current rat-
ings greater than 200 mA. A 47 μF/50V low ESR electrolytic
capacitor capacitor is needed.
For a through hole design, a 47 μF/50V electrolytic capacitor
(Panasonic HFQ series or Nichicon PL series or equivalent)
would be adequate. Other types or other manufacturers ca-
pacitors can be used provided the RMS ripple current ratings
are adequate.
For surface mount designs, solid tantalum capacitors are
recommended. The TPS series available from AVX, and the
593D series from Sprague are both surge current tested.
To further simplify the buck regulator design procedure, Na-
tional Semiconductor is making available computer design
software to be used with the Simple Switcher line ot switch-
ing regulators.
Switchers Made Simple
(version 4.1 or later)
is available from National’s web site, www.national.com.
Output
Volt-
age
(V)
Through Hole Output Capacitor
Panasonic
Nichicon PL
HFQ Series
(μF/V)
220/25
180/25
82/25
82/25
82/25
82/25
82/50
82/50
Surface Mount Output Capacitor
AVX TPS
Sprague
Series
595D Series
(μF/V)
(μF/V)
220/10
220/10
100/10
120/10
100/10
120/10
100/16
100/16
100/16
100/16
68/20
100/20
10/35
15/35
10/35
15/35
Feedforward
Capacitor
Feedforward
Capacitor
Series
(μF/V)
220/25
180/25
82/25
82/25
82/25
82/25
120/50
120/50
1.2
4
6
9
1 2
1 5
2 4
2 8
0
0
4.7 nF
4.7 nF
3.3 nF
2.2 nF
1.5 nF
1 nF
820 pF
4.7 nF
4.7 nF
3.3 nF
2.2 nF
1.5 nF
220 pF
220 pF
FIGURE 3. Output Capacitor and Feedforward Capacitor Selection Table
L
www.national.com
14
相關PDF資料 |
PDF描述 |
|---|---|
| LM2598SX-5.0 | Voltage-Mode SMPS Controller |
| LM2595J-5.0-QML | Voltage-Mode SMPS Controller |
| LM2595SX-12 | Voltage-Mode SMPS Controller |
| LM2595SX-3.3 | Voltage-Mode SMPS Controller |
| LM2595SX-5.0 | Voltage-Mode SMPS Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM2598S-12 | 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| LM2598S-12/NOPB | 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| LM2598S12P+ | 制造商:Texas Instruments 功能描述: |
| LM2598S-12P+ | 制造商:Texas Instruments 功能描述:2.6 A SWITCHING REGULATOR, 173 kHz SWITCHING FREQ-MAX, PSSO7 |
| LM2598S-3.3 | 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
發(fā)布緊急采購，3分鐘左右您將得到回復。