- 您現在的位置：買賣IC網 > PDF目錄95790 > LM2575INE4 (TEXAS INSTRUMENTS INC) 4 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, PDIP16 PDF資料下載
參數資料
| 型號： | LM2575INE4 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | 4 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, PDIP16 |
| 封裝： | ROHS COMPLIANT, PLASTIC, MS-001BB, DIP-16 |
| 文件頁數： | 8/10頁 |
| 文件大?。?/td> | 185K |
| 代理商： | LM2575INE4 |
www.ti.com
Output Voltage Ripple and Transients
Feedback Connection
ON/OFF Input
Grounding
1-A SIMPLE STEP-DOWN SWITCHING VOLTAGE REGULATOR
SLVS569E – JANUARY 2005 – REVISED JANUARY 2006
APPLICATION INFORMATION (continued)
As with any switching power supply, the output of the LM2575 has a sawtooth-ripple voltage at the switching
frequency. Typically about 1% of the output voltage, this ripple is due mainly to the inductor sawtooth-ripple
current and the ESR of the output capacitor (see note on COUT). Furthermore, the output also may contain small
voltage spikes at the peaks of the sawtooth waveform. This is due to the fast switching of the output switch and
the parasitic inductance of COUT. These voltage spikes can be minimized through the use of low-inductance
capacitors.
There are several ways to reduce the output ripple voltage: a larger inductor, a larger COUT, or both. Another
method is to use a small LC filter (20
H and 100 F) at the output. This filter can reduce the output ripple
voltage by a factor of 10 (see Figure 1).
FEEDBACK must be connected between the two programming resistors. Again, both of these resistors should be
in close proximity to the regulator, and each should be less than 100 k
to minimize noise pickup.
ON/OFF should be grounded or be a low-level TTL voltage (typically <1.6 V) for normal operation. To shut down
the LM2575 and put it in standby mode, a high-level TTL or CMOS voltage should be supplied to this pin.
ON/OFF should not be left open and safely can be pulled up to VIN with or without a pullup resistor.
The power and ground connections of the LM2575 must be low impedance to help maintain output stability. With
the 16-pin package, all the ground pins (including signal and power grounds) should be soldered directly to wide
PCB copper traces to ensure low-inductance connections and good thermal dissipation.
7
相關PDF資料 |
PDF描述 |
|---|---|
| LM2575IN | 4 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, PDIP16 |
| LM2575K-5.0 | SWITCHING REGULATOR, 52 kHz SWITCHING FREQ-MAX, MBFM2 |
| LM2688M-ADJ | 1.4 A SWITCHING REGULATOR, 173 kHz SWITCHING FREQ-MAX, PDSO8 |
| LM2720M/NOPB | SWITCHING CONTROLLER, 8700 kHz SWITCHING FREQ-MAX, PDSO24 |
| LM2760M5/NOPB | SWITCHED CAPACITOR REGULATOR, 750 kHz SWITCHING FREQ-MAX, PDSO5 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM2575M-12 | 制造商:OC White Company 功能描述:Conv DC-DC Single Step Down 4V to 40V 24-Pin SOIC W |
| LM2575M-12/NOPB | 功能描述:IC REG BUCK 12V 1A 24-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:SIMPLE SWITCHER® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:3.3V 輸入電壓:4.5 V ~ 24 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:125mA 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 包裝:Digi-Reel® 供應商設備封裝:SOT-6 其它名稱:MAX1836EUT33#TG16DKR |
| LM2575M-15 | 制造商:OC White Company 功能描述:Conv DC-DC Single Step Down 4V to 40V 24-Pin SOIC W |
| LM2575M-15/NOPB | 功能描述:IC REG BUCK 15V 1A 24-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:SIMPLE SWITCHER® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:3.3V 輸入電壓:4.5 V ~ 24 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:125mA 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 包裝:Digi-Reel® 供應商設備封裝:SOT-6 其它名稱:MAX1836EUT33#TG16DKR |
| LM2575M-3.3 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Texas Instruments 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。