參數資料
型號: LM2418T
廠商: NATIONAL SEMICONDUCTOR CORP
元件分類: 音頻/視頻放大
英文描述: Triple 30 MHz CRT Driver
中文描述: 3 CHANNEL, VIDEO AMPLIFIER, PSFM11
封裝: HEAT SINK, PLASTIC, TO-220, 11 PIN
文件頁數: 3/6頁
文件大小: 130K
代理商: LM2418T
LM2418DTheory of Operation
The LM2418 is a high voltage triple CRT driver suitable for
VGA display applications. The LM2418 features 90V opera-
tion and low power dissipation. The part is housed in the
industry standard 11-lead TO-220 molded power package.
The heat sink is electrically isolated from the circuitry and
may be grounded for ease of manufacturing and RFI shield-
ing.
The circuit diagram of the LM2418 is shown inFigure 1. Q1
and R2 provide a conversion of input voltage to current,
while Q2 acts as a common base or cascode amplifier stage
to drive the load resistor R1. Emitter followers Q3 and Q4
isolate the impedance of R1 from the capacitance of the
CRT cathode, and make the circuit relatively insensitive to
load capacitance. The gain of this circuit is
b
R1/R2 and is
fixed at
b
19. The bandwidth of the circuit is set by the
collector time constant formed by the load resistor R1 and
associated capacitance of Q2, Q3, Q4, and stray layout ca-
pacitance. Diodes D1 and D2 provide forward bias to the
output stage to reduce crossover distortion at low signal
levels, while R3 provides a DC bias offset to match the out-
put level characteristics of the LM1203 RGB Video Amplifier
System. Proprietary transistor design allows for high band-
width with low operating power.
Figure 2 shows a typical test circuit for evaluation of the
LM2418. This circuit is designed to allow testing of the
LM2418 in a 50
X
environment such as a pulse generator
and a scope, or a network analyzer. In this test circuit, two
resistors in series totaling 4.95 k
X
form a wideband low
capacitance probe to match the output of the LM2418 to a
50
X
cable and load. Typical AC performance of the circuit is
shown in Figure 3. The input signal is AC coupled to the
base of Q1, while a DC bias of 12V is applied to the base of
Q2 (See Figure 2).
Thermal Considerations
The transfer characteristics of the amplifier are shown in
Figures 4 and 5. Power supply current increases as the in-
put signal increases and consequently power dissipation
also increases.
The LM2418 cannot be used without heat sinking. Figure 5
shows the power dissipated in each channel over the oper-
ating voltage range of the device. Typical ‘‘a(chǎn)verage’’ power
dissipation with the device output voltage at one half the
supply voltage is 1.8W per channel for a total dissipation of
5.4W package dissipation. Under white screen conditions,
i.e., 20V output, dissipation increases to 3.0W per channel
or 9W total. The LM2418 case temperature must be main-
tained below 100
§
C. If the maximum expected ambient tem-
perature is 60
§
C, then a maximum heat sink thermal resist-
ance can be calculated:
R
th
e
(100
§
C
b
60
§
C)
9W
e
4.4
§
C/W
PRECAUTION:
AGAINST OUTPUT SHORT CIRCUITS. The minimum re-
sistance the LM2418 can drive is 800
X
to ground or V
a
.
THE
LM2418
IS
NOT
PROTECTED
TL/K/11125–7
FIGURE 4. LM2418 DC Characteristics
TL/K/11125–9
FIGURE 5. LM2418 Output Swing
and Power Characteristics
3
相關PDF資料
PDF描述
LM2451 220V Monolithic Triple Channel 12 MHz DC Coupled CRT DTV Driver
LM2451TB 220V Monolithic Triple Channel 12 MHz DC Coupled CRT DTV Driver
LM2481NA 145V Triple Bias Clamp
LM25005 42V, 2.5A STEP-DOWN SWITCHING REGULATOR
LM25005MH 42V, 2.5A STEP-DOWN SWITCHING REGULATOR
相關代理商/技術參數
參數描述
LM2419 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Triple 65 MHz CRT Driver
LM2419T 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel
LM242 制造商:LM TECHNOLOGIES 功能描述:BASE UNIT SMA CONNX W/1.5M CABLE 制造商:LM TECHNOLOGIES 功能描述:BASE UNIT, SMA CONNX W/1.5M CABLE 制造商:LM TECHNOLOGIES 功能描述:BASE UNIT, SMA CONNX W/1.5M CABLE; Impedance:50ohm ;RoHS Compliant: Yes
LM2421 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Monolithic Triple Channel HDTV Driver
LM242-155.52M 制造商:CONNOR-WINFIELD 制造商全稱:Connor-Winfield Corporation 功能描述:5.0x7.0mm Surface Mount LVDS Clock Oscillator Series