- 您現在的位置：買賣IC網 > PDF目錄358815 > LM208AJ Voltage-Feedback Operational Amplifier PDF資料下載
參數資料
| 型號： | LM208AJ |
| 英文描述： | Voltage-Feedback Operational Amplifier |
| 中文描述： | 電壓反饋運算放大器 |
| 文件頁數： | 5/8頁 |
| 文件大小： | 158K |
| 代理商： | LM208AJ |
Application Hints
A very low drift amplifier poses some uncommon application
and testing problems. Many sources of error can cause the
apparent circuit drift to be much higher than would be pre-
dicted.
Thermocouple effects caused by temperature gradient
across dissimilar metals are perhaps the worst offenders.
Only a few degrees gradient can cause hundreds of micro-
volts of error. The two places this shows up, generally, are
the package-to-printed circuit board interface and tempera-
ture gradients across resistors. Keeping package leads
short and the two input leads close together helps greatly.
Resistor choice as well as physical placement is important
for minimizing thermocouple effects. Carbon, oxide film and
some metal film resistors can cause large thermocouple er-
rors. Wirewound resistors of evanohm or manganin are best
since they only generate about 2
m
V/
§
C referenced to cop-
per. Of course, keeping the resistor ends at the same tem-
perature is important. Generally, shielding a low drift stage
electrically and thermally will yield good results.
Resistors can cause other errors besides gradient generat-
ed voltages. If the gain setting resistors do not track with
temperature a gain error will result. For example, a gain of
1000 amplifier with a constant 10 mV input will have a 10V
output. If the resistors mistrack by 0.5% over the operating
temperature range, the error at the output is 50 mV. Re-
ferred to input, this is a 50
m
V error. All of the gain fixing
resistor should be the same material.
Testing low drift amplifiers is also difficult. Standard drift
testing technique such as heating the device in an oven and
having the leads available through a connector, thermo-
probe, or the soldering iron methodDdo not work. Thermal
gradients cause much greater errors than the amplifier drift.
Coupling microvolt signal through connectors is especially
bad since the temperature difference across the connector
can be 50
§
C or more. The device under test along with the
gain setting resistor should be isothermal.
Schematic Diagram
TL/H/7759–6
5
相關PDF資料 |
PDF描述 |
|---|---|
| LM208AH | Operational Amplifiers |
| LM208AJ-8 | CAC 5C 5#16S PIN RECP BOX |
| LM208 | Operational Amplifiers |
| LM20X21A | Character Type LCD Module(FA/POS/Measuring instruments) |
| LM211D | HIGH PERFORMANCE VOLTAGE COMPARATORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM208AJ-8 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Operational Amplifiers |
| LM208AN | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Voltage-Feedback Operational Amplifier |
| LM208AN/B+ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Voltage-Feedback Operational Amplifier |
| LM208AP | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Voltage-Feedback Operational Amplifier |
| LM208D | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Voltage-Feedback Operational Amplifier |
發布緊急采購，3分鐘左右您將得到回復。