- 您現在的位置：買賣IC網 > PDF目錄384596 > LM20154MHX (NATIONAL SEMICONDUCTOR CORP) 4A, 1MHz PowerWise㈢ Synchronous Buck Regulator with SYNCOUT PDF資料下載
參數資料
| 型號： | LM20154MHX |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 4A, 1MHz PowerWise㈢ Synchronous Buck Regulator with SYNCOUT |
| 中文描述： | 6.6 A SWITCHING REGULATOR, 1150 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封裝： | TSSOP-16 |
| 文件頁數： | 10/22頁 |
| 文件大?。?/td> | 631K |
| 代理商： | LM20154MHX |
Operation Description
GENERAL
The LM20154 switching regulator features all of the functions
necessary to implement an efficient low voltage buck regula-
tor using a minimum number of external components. This
easy to use regulator features two integrated switches and is
capable of supplying up to 4A of continuous output current.
The regulator utilizes peak current mode control with nonlin-
ear slope compensation to optimize stability and transient
response over the entire output voltage range. Peak current
mode control also provides inherent line feed-forward, cycle-
by-cycle current limiting and easy loop compensation. The
fixed 1 MHz operating frequency minimizes the inductor size
while still achieving efficiencies up to 96%. The precision in-
ternal voltage reference allows the output to be set as low as
0.8V. Fault protection features include: current limiting, ther-
mal shutdown, over voltage protection, and shutdown capa-
bility. The device is available in the eTSSOP-16 package
featuring an exposed pad to aid thermal dissipation. The
LM20154 can be used in numerous applications to efficiently
step-down from a 5V or 3.3V bus. The typical application cir-
cuit for the LM20154 is shown in
Figure 2
in the design guide.
PRECISION ENABLE
The enable (EN) pin allows the output of the device to be en-
abled or disabled with an external control signal. This pin is a
precision analog input that enables the device when the volt-
age exceeds 1.18V (typical). The EN pin has 66 mV of hys-
teresis and will disable the output when the enable voltage
falls below 1.11V (typical). If the EN pin is not used, it should
be connected to VIN. Since the enable pin has a precise turn
on threshold it can be used along with an external resistor
divider network from V
to configure the device to turn on at
a precise input voltage. The precision enable circuitry will re-
main active even when the device is disabled.
CLOCK SYNCHRONIZATION OUTPUT
The SYNCOUT pin is an open drain output that provides a
signal that is the same frequency as the internal oscillator but
is 180 degrees out of phase with the switch voltage. The
SYNCOUT pin requires an external pull-up resistor to set the
high level. For most applications a 2.94 k
pull-up connected
to the input voltage should be sufficient. Since the SYNCOUT
is out of phase with the switch voltage it can be used with other
devices with a synchronization input such as the LM20134 to
run multiple convertors out of phase. Running multiple con-
verters out of phase reduces the RMS current requirements
for the input capacitor, value of the input capacitor, and con-
ducted EMI back through the input bus.
PEAK CURRENT MODE CONTROL
In most cases, the peak current mode control architecture
used in the LM20154 only requires two external components
to achieve a stable design. The compensation can be select-
ed to accommodate any capacitor type or value. The external
compensation also allows the user to set the crossover fre-
quency and optimize the transient performance of the device.
For duty cycles above 50% all current mode control buck
converters require the addition of an artificial ramp to avoid
sub-harmonic oscillation. This artificial linear ramp is com-
monly referred to as slope compensation. What makes the
LM20154 unique is the amount of slope compensation will
change depending on the output voltage. When operating at
high output voltages the device will have more slope com-
pensation than when operating at lower output voltages. This
is accomplished in the LM20154 by using a non-linear
parabolic ramp for the slope compensation. The parabolic
slope compensation of the LM20154 is much better than the
traditional linear slope compensation because it optimizes the
stability of the device over the entire output voltage range.
CURRENT LIMIT
The precise current limit of the LM20154 is set at the factory
to be within 10% over the entire operating temperature range.
This enables the device to operate with smaller inductors that
have lower saturation currents. When the peak inductor cur-
rent reaches the current limit threshold, an over current event
is triggered and the internal high-side FET turns off and the
low-side FET turns on allowing the inductor current to ramp
down until the next switching cycle. For each sequential over-
current event, the reference voltage is decremented and
PWM pulses are skipped resulting in a current limit that does
not aggressively fold back for brief over-current events, while
at the same time providing frequency and voltage foldback
protection during hard short circuit conditions.
SOFT-START AND VOLTAGE TRACKING
The SS/TRK pin is a dual function pin that can be used to set
the start up time or track an external voltage source. The start
up or Soft-Start time can be adjusted by connecting a capac-
itor from the SS/TRK pin to ground. The Soft-Start feature
allows the regulator output to gradually reach the steady state
operating point, thus reducing stresses on the input supply
and controlling start up current. If no Soft-Start capacitor is
used the device defaults to the internal Soft-Start circuitry re-
sulting in a start up time of approximately 1 ms. For applica-
tions that require a monotonic start up or utilize the PGOOD
pin, an external Soft-Start capacitor is recommended. The
SS/TRK pin can also be set to track an external voltage
source. The tracking behavior can be adjusted by two external
resistors connected to the SS/TRK pin as shown in
Figure 7
in the design guide.
PRE-BIAS START UP CAPABILITY
The LM20154 is in a pre-biased state when the device starts
up with an output voltage greater than zero. This often occurs
in many multi-rail applications such as when powering an FP-
GA, ASIC, or DSP. In these applications the output can be
pre-biased through parasitic conduction paths from one sup-
ply rail to another. Even though the LM20154 is a syn-
chronous converter it will not pull the output low when a
prebias condition exists. During start up the LM20154 will not
sink current until the Soft-Start voltage exceeds the voltage
on the FB pin. Since the device can not sink current it protects
the load from damage that might otherwise occur if current is
conducted through the parasitic paths of the load.
POWER GOOD AND OVER VOLTAGE FAULT HANDLING
The LM20154 has built in under and over voltage compara-
tors that control the power switches. Whenever there is an
excursion in output voltage above the set OVP threshold, the
part will terminate the present on-pulse, turn on the low-side
FET, and pull the PGOOD pin low. The low-side FET will re-
main on until either the FB voltage falls back into regulation
or the zero cross detection is triggered which in turn tri-states
the FETs. If the output reaches the UVP threshold the part will
continue switching and the PGOOD pin will be asserted and
go low. Typical values for the PGOOD resistor are on the or-
der of 100 k
or less. To avoid false tripping during transient
glitches the PGOOD pin has 16 μs of built in deglitch time to
both rising and falling edges.
www.national.com
10
L
相關PDF資料 |
PDF描述 |
|---|---|
| LM20242 | 36V, 2A PowerWise㈢ Adjustable Frequency Synchronous Buck Regulator |
| LM20242MH | 36V, 2A PowerWise㈢ Adjustable Frequency Synchronous Buck Regulator |
| LM20242MHE | 36V, 2A PowerWise㈢ Adjustable Frequency Synchronous Buck Regulator |
| LM20242MHX | 36V, 2A PowerWise㈢ Adjustable Frequency Synchronous Buck Regulator |
| LM205 | Voltage Regulators |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM20154MHX/NOPB | 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| LM201A | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:SINGLE OPERATIONAL AMPLIFIER |
| LM201AD | 功能描述:運算放大器 - 運放 Gain Band-w 3.5MHz Dissipation 300mW RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| LM201ADG | 功能描述:運算放大器 - 運放 Precision Single Chnl -25 to 85deg C RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| LM201ADG | 制造商:ON Semiconductor 功能描述:OP AMP SINGLE NON COMPENSATED 201 制造商:ON Semiconductor 功能描述:OP AMP, SINGLE NON COMPENSATED, 201 制造商:ON Semiconductor 功能描述:OP AMP, SINGLE NON COMPENSATED, 201; Op Amp Type:General Purpose; No. of Amplifiers:1; Slew Rate:10V/s; Supply Voltage Range: 5V to 20V; Amplifier Case Style:SOIC; No. of Pins:8; Operating Temperature Min:-25C; Operating ;RoHS Compliant: Yes |
發布緊急采購，3分鐘左右您將得到回復。