- 您現在的位置：買賣IC網 > PDF目錄358810 > LM135A PDF資料下載
參數資料
| 型號： | LM135A |
| 文件頁數： | 5/14頁 |
| 文件大?。?/td> | 291K |
| 代理商： | LM135A |
Typical Performance Characteristics
(Continued)
Application Hints
CALIBRATING THE LM135
Included on the LM135 chip is an easy method of calibrating
the device for higher accuracies. A pot connected across the
LM135 with the arm tied to the adjustment terminal allows a
1-point calibration of the sensor that corrects for inaccuracy
over the full temperature range.
This single point calibration works because the output of the
LM135 is proportional to absolute temperature with the ex-
trapolated output of sensor going to 0V output at 0K
(273.15C). Errors in output voltage versus temperature are
only slope (or scale factor) errors so a slope calibration at
one temperature corrects at all temperatures.
The output of the device (calibrated or uncalibrated) can be
expressed as:
where T is the unknown temperature and T
o
is a reference
temperature, both expressed in degrees Kelvin. By calibrat-
ing the output to read correctly at one temperature the output
at all temperatures is correct. Nominally the output is cali-
brated at 10 mV/K.
Typical Applications
To insure good sensing accuracy several precautions must
be taken. Like any temperature sensing device, self heating
can reduce accuracy. The LM135 should be operated at the
lowest current suitable for the application. Sufficient current,
of course, must be available to drive both the sensor and the
calibration pot at the maximum operating temperature as
well as any external loads.
If the sensor is used in an ambient where the thermal resis-
tance is constant, self heating errors can be calibrated out.
This is possible if the device is run with a temperature stable
current. Heating will then be proportional to zener voltage
and therefore temperature. This makes the self heating error
proportional to absolute temperature the same as scale
factor errors.
WATERPROOFING SENSORS
Meltable inner core heat shrinkable tubing such as manufac-
tured by Raychem can be used to make low-cost waterproof
sensors. The LM335 is inserted into the tubing about
1
2
"
from the end and the tubing heated above the melting point
of the core. The unfilled
1
2
" end melts and provides a seal
over the device.
Thermal Response in Stirred Oil Bath
DS005698-36
Forward Characteristics
DS005698-37
Basic Temperature Sensor
DS005698-2
Calibrated Sensor
DS005698-9
*Calibrate for 2.982V at 25C
Wide Operating Supply
DS005698-10
L
www.national.com
5
相關PDF資料 |
PDF描述 |
|---|---|
| LM135Z | PRECISION TEMPERATURE SENSORS |
| LM135D | PRECISION TEMPERATURE SENSORS |
| LM135AZ | PRECISION TEMPERATURE SENSORS |
| LM135AD | PRECISION TEMPERATURE SENSORS |
| LM135H | Precision Temperature Sensors |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM135AD | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:PRECISION TEMPERATURE SENSORS |
| LM135AH | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| LM135AH/NOPB | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| LM135AZ | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:PRECISION TEMPERATURE SENSORS |
| LM135D | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:PRECISION TEMPERATURE SENSORS |
發布緊急采購，3分鐘左右您將得到回復。