- 您現在的位置：買賣IC網 > PDF目錄44027 > LK5660-9PD8B1 (POWER-ONE INC) 2-OUTPUT 150 W AC-DC PWR FACTOR CORR MODULE PDF資料下載
參數資料
| 型號： | LK5660-9PD8B1 |
| 廠商： | POWER-ONE INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 2-OUTPUT 150 W AC-DC PWR FACTOR CORR MODULE |
| 封裝： | METAL, CASE K02, MODULE |
| 文件頁數： | 17/28頁 |
| 文件大?。?/td> | 1215K |
| 代理商： | LK5660-9PD8B1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
K Series
AC-DC Converters >100 Watt
Rugged Environment
Edition 4/4.99
24/28
MELCHER
The Power Partners.
Vo1+
Vo1–
D
UD
ID
Rp
Input
11007
NPN output (D5...DD):
Connector pin D is internally connected via the collector-
emitter path of a NPN transistor to the negative potential of
output 1.
UD
< 0.4 V (logic low) corresponds to a monitored
voltage level (
Ui and/or Uo1)
> U
t + Uh. The current ID
through the open collector should not exceed 20 mA. The
NPN output is not protected against external overvoltages.
UD should not exceed 40 V.
Ui, Uo1 status
D output,
UD
Ui or Uo1 < Ut
high, H,
ID ≤ 25 A at UD = 40 V
Ui and Uo1 > Ut + Uh
low, L,
UD ≤ 0.4 V at ID = 20 mA
Fig. 37
Option D5...DD: NPN output, Uo1
≤ 40 V, I
D
≤ 20 mA
Table 19: D-output logic signals
Version of D
Ui < Ut resp. Uo < Ut
Ui > Ut + Uh resp. Uo > Ut
Conguration
D1, D2, D3, D4, D0
low
high
JFET
D5, D6, D7, D8, D9, DD
high
low
NPN
Option D Undervoltage monitor
The input and/or output undervoltage monitoring circuit op-
erates independently of the built-in input undervoltage lock-
out circuit. A logic "low" (JFET output) or "high" signal (NPN
output) is generated at pin 20 as soon as one of the moni-
tored voltages drops below the preselected threshold level
Ut. The return for this signal is Vo1–. The D output reco-
vers when the monitored voltage(s) exceed(s)
Ut + Uh. The
Table 18: Undervoltage monitoring functions
Output type
Monitoring
Minimum adjustment range
Typical hysteresis
Uho [% of Ut]
JFET
NPN
U i
Uo1
of threshold level
U t
for
U t min...U t max
Uti
Uto
Uho
D1
D5
no
yes
-
3.5...40 V 1
2.5...0.6
D2
D6
yes
no
355 V DC 4
--
D3
D7
yes
355 V DC 4
(0.95...0.985
Uo1) 2
"0"
D4
D8
no
yes
-
(0.95...0.985
Uo1) 2
"0"
D0
D9
no
yes
-
3.5...40 V 3
2.5...0.6
yes
355 V DC 4
3.5...40 V 3
2.5...0.6
DD
yes
355 V DC4
3.5...40 V 1
2.5...0.6
1 Threshold level adjustable by potentiometer
2 Fixed value. Tracking if Uo1 adjusted via R-input, option P or sense lines.
3 The threshold level permanently adjusted according to customer specication
±2% at 25°C. Any value within the specied range is
basically possible but causes a special type designation in addition to the standard option designations (D0/D9)!
4 Option D monitors the boost regulator output voltage. The trigger level is adjusted in the factory to 355 V DC.
threshold level
Uti is adjusted in the factory. The threshold
level
Uto is either adjusted by a potentiometer, accessible
through a hole in the front cover, or factory adjusted to a
xed value specied by the customer.
Option D exists in various versions D0...DD as shown in the
following table.
Vo1+
Vo1–
D
UD
ID
Rp
Input
11006
Fig. 36
Option D0...D4: JFET output, ID
≤ 2.5 mA
JFET output (D0…D4):
Connector pin D is internally connected via the drain-
source path of a JFET (self-conducting type) to the nega-
tive potential of output 1.
UD
≤ 0.4 V (logic low) corresponds
to a monitored voltage level (
Ui and/or Uo1)
<U
t. The cur-
rent
ID through the JFET should not exceed 2.5 mA. The
JFET is protected by a 0.5 W Zener diode of 8.2 V against
external overvoltages.
Ui, Uo1 status
D output,
UD
Ui or Uo1 < Ut
low, L,
UD ≤ 0.4 V at ID = 2.5 mA
Ui and Uo1 > Ut + Uh
high, H,
ID ≤ 25 A at UD = 5.25 V
相關PDF資料 |
PDF描述 |
|---|---|
| LK5660-9PD8T | 2-OUTPUT 150 W AC-DC PWR FACTOR CORR MODULE |
| LK5660-9RD1B2 | 2-OUTPUT 150 W AC-DC PWR FACTOR CORR MODULE |
| LK5660-9RD3TB1 | 2-OUTPUT 150 W AC-DC PWR FACTOR CORR MODULE |
| LK5660-9RD5TB2 | 2-OUTPUT 150 W AC-DC PWR FACTOR CORR MODULE |
| LK5660-9RD6TB1 | 2-OUTPUT 150 W AC-DC PWR FACTOR CORR MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LK-590-001 | 功能描述:LED MODULE 1W AMBER RoHS:是 類別:光電元件 >> LED - 高亮度電源模塊 系列:- 標準包裝:36 系列:5027 TFFC STAR K2 顏色:暖白色 配置:星形 在特定電流下的光通量 - 測試:75lm 電流 - 測試:350mA 電流 - 最大:1.5A 帶連接器:無 驅動器電路:無 波長:- 電壓:- |
| LK-590-001-FC | 功能描述:LED MODULE 1W AMBER W/CONN RoHS:是 類別:光電元件 >> LED - 高亮度電源模塊 系列:- 標準包裝:36 系列:5027 TFFC STAR K2 顏色:暖白色 配置:星形 在特定電流下的光通量 - 測試:75lm 電流 - 測試:350mA 電流 - 最大:1.5A 帶連接器:無 驅動器電路:無 波長:- 電壓:- |
| LK-59A-1 | 制造商:ITT Interconnect Solutions 功能描述:OBS - Bulk |
| LK-59A-2 | 制造商:ITT Interconnect Solutions 功能描述:OBS - Bulk 制造商:Sure Seal Connections 功能描述:STD-K LK PLUG D/C W/CHAIN |
| LK5AGB126M3 | 功能描述:Keylock Switch 2 Position SPDT 4A (AC/DC) 125V (AC) 28V (DC) Panel Mount 制造商:apem inc. 系列:LK 零件狀態:在售 電路:SPDT 針腳數:2 開關功能:開-瞬時 接觸時間:未指定 額定電流:4A（AC/DC） 額定電壓 - AC:125V 額定電壓 - DC:28V 致動器類型:扁平按鍵 鑰匙拔出位置:僅 1 拋射角:45° 觸頭材料:銅合金 觸頭鍍層:金 安裝類型:面板安裝 端子類型:焊片 面板開口尺寸:圓形 - 19.00mm 直徑 特性:- 法蘭后深度:32.55mm 工作溫度:-30°C ~ 85°C 機械壽命:6，000 次循環 電氣壽命:6，000 次循環 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。