參數(shù)資料
型號: LK1301-9RD6B2
元件分類: 電源模塊
英文描述: 1-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE
封裝: METAL, CASE K02, MODULE
文件頁數(shù): 14/26頁
文件大?。?/td> 601K
代理商: LK1301-9RD6B2
Cassette Style
150 Watt AC-DC Converters
K Series
Edition 01/01.2001
21/26
D Undervoltage Monitor
The input and/or output undervoltage monitoring circuit op-
erates independently of the built-in input undervoltage lock-
out circuit. A logic "low" (JFET output) or "high" signal (NPN
output) is generated at pin 20 as soon as one of the moni-
tored voltages drops below the preselected threshold level
Ut. The return for this signal is Vo1–. The D output recovers
when the monitored voltage(s) exceed(s)
Ut + Uh. The
Table 18: Undervoltage monitor functions
Output type
Monitoring
Minimum adjustment range
Typical hysteresis
Uh [% of Ut]
JFET
NPN
U i
Uo1
of threshold level
U t
for
U t min...U t max
Uti
Uto
Uhi
Uho
D1
D5
no
yes
-
3.5...40 V 1
-
2.5...0.6
D2
D6
yes
no
Ui min...Ui max 1
-
3.4...0.4
-
D3
D7
yes
Ui min...Ui max 1
(0.95...0.985
Uo1) 2
3.4...0.4
"0"
D4
D8
no
yes
-
(0.95...0.985
Uo1) 2
-"0"
D0
D9
no
yes
-
3.5...40 V 3
-
2.5...0.6
yes
no
Ui min...Ui max 3 4
-
3.4...0.4
-
yes
Ui min...Ui max 3 4
3.5...40 V 3
3.4...0.4
2.5...0.6
yes
Ui min...Ui max 3 4
(0.95...0.985
Uo1) 2
3.4...0.4
"0"
-
DD
yes
Ui min...Ui max 1
3.5...40 V 1
3.4...0.4
2.5...0.6
1 Threshold level adjustable by potentiometer
2 Fixed value. Tracking if U01 is adjusted via R-input, option P or sense lines.
3 The threshold level permanently adjusted according to customer specification
±2% at 25°C. Any value within the specified range is
basically possible but causes a special type designation in addition to the standard option designations (D0/D9 respectively)!
4 Adjusted at Io nom
threshold level
Uti is adjusted in the factory. The threshold
level
Uto is either adjusted by a potentiometer, accessible
through a hole in the front cover, or factory adjusted to a
xed value specied by the customer.
Option D exists in various versions D0...DD as shown in the
following table.
Fig. 30
Paralleling of single output units using option T with the
sense lines connected at the load
1 Leads should have equal length and cross sections and should
run in the same cable loom.
2 Diodes recommended in redundant operation only
3 DC common point
Vo+
Vo–
Vo+
Vo–
Load
Vo+
Vo–
11003
T Current Sharing
This option ensures that the output currents are approxi-
mately shared between all paralleled modules and in-
creases system reliability. To use this facility, simply inter-
connect the T pins of all modules and make sure, that
pins 14, the S– pin (LK 1000) or the Vo1– pins (LK 2000)
are also connected together. The load leads should have
equal length and cross section to ensure equal voltage
drops. Not more than 5 units should be connected in paral-
lel. If output voltage adjustment is requested we strongly
recommend to use the R-input instead of option P, as with
option P the required setting accuracy is difcult to achieve.
Fig. 31
An example of poor wiring for connection in parallel
Load
1
2
3
S+
Vo+
Vo–
S–
N
P
T
N
P
S+
Vo+
Vo–
S–
T
1
max. 5 units connected in parallel
11004
Fig. 32
Paralleling of double output units using option T with
Power bus.
Load
max. 5 units in parallel connection
+
Power bus
Module
Vo2–
Vo2+
Vo1–
Vo1+
T
Module
Vo2–
Vo2+
Vo1–
Vo1+
T
11037
The output voltages must be individually set prior to paral-
leling to within a tolerance of 1...2% or the R pins should be
connected together.
相關PDF資料
PDF描述
LK1501-7PD2B2 1-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE
LK1501-9PDDB1 1-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE
LK1601-7ERD0TB2 1-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE
LK1601-7ERDDB2 1-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE
LK1601-7PD9TB2 1-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE
相關代理商/技術參數(shù)
參數(shù)描述
LK-14 制造商:Shinagawa Shoko 功能描述:
LK14 Y/R 制造商:Altech Corporation 功能描述:
LK14-LFR 制造商:FRONTIER 制造商全稱:Frontier Electronics. 功能描述:1A SURFACE MOUNT SCHOTTKY BARRIER RECTIFIERS
LK-15 制造商:Shinagawa Shoko 功能描述:
LK150145A 制造商:PLA 功能描述:OF514X15KV N5F4A