- 您現在的位置：買賣IC網 > PDF目錄43985 > LK1001-9EPDD 1-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | LK1001-9EPDD |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE |
| 封裝： | HEAT SINK, METAL, CASE K02, MODULE |
| 文件頁數： | 14/26頁 |
| 文件大?。?/td> | 601K |
| 代理商： | LK1001-9EPDD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁
Cassette Style
150 Watt AC-DC Converters
K Series
Edition 01/01.2001
21/26
D Undervoltage Monitor
The input and/or output undervoltage monitoring circuit op-
erates independently of the built-in input undervoltage lock-
out circuit. A logic "low" (JFET output) or "high" signal (NPN
output) is generated at pin 20 as soon as one of the moni-
tored voltages drops below the preselected threshold level
Ut. The return for this signal is Vo1–. The D output recovers
when the monitored voltage(s) exceed(s)
Ut + Uh. The
Table 18: Undervoltage monitor functions
Output type
Monitoring
Minimum adjustment range
Typical hysteresis
Uh [% of Ut]
JFET
NPN
U i
Uo1
of threshold level
U t
for
U t min...U t max
Uti
Uto
Uhi
Uho
D1
D5
no
yes
-
3.5...40 V 1
-
2.5...0.6
D2
D6
yes
no
Ui min...Ui max 1
-
3.4...0.4
-
D3
D7
yes
Ui min...Ui max 1
(0.95...0.985
Uo1) 2
3.4...0.4
"0"
D4
D8
no
yes
-
(0.95...0.985
Uo1) 2
-"0"
D0
D9
no
yes
-
3.5...40 V 3
-
2.5...0.6
yes
no
Ui min...Ui max 3 4
-
3.4...0.4
-
yes
Ui min...Ui max 3 4
3.5...40 V 3
3.4...0.4
2.5...0.6
yes
Ui min...Ui max 3 4
(0.95...0.985
Uo1) 2
3.4...0.4
"0"
-
DD
yes
Ui min...Ui max 1
3.5...40 V 1
3.4...0.4
2.5...0.6
1 Threshold level adjustable by potentiometer
2 Fixed value. Tracking if U01 is adjusted via R-input, option P or sense lines.
3 The threshold level permanently adjusted according to customer specification
±2% at 25°C. Any value within the specified range is
basically possible but causes a special type designation in addition to the standard option designations (D0/D9 respectively)!
4 Adjusted at Io nom
threshold level
Uti is adjusted in the factory. The threshold
level
Uto is either adjusted by a potentiometer, accessible
through a hole in the front cover, or factory adjusted to a
xed value specied by the customer.
Option D exists in various versions D0...DD as shown in the
following table.
Fig. 30
Paralleling of single output units using option T with the
sense lines connected at the load
1 Leads should have equal length and cross sections and should
run in the same cable loom.
2 Diodes recommended in redundant operation only
3 DC common point
Vo+
Vo–
Vo+
Vo–
Load
Vo+
Vo–
11003
T Current Sharing
This option ensures that the output currents are approxi-
mately shared between all paralleled modules and in-
creases system reliability. To use this facility, simply inter-
connect the T pins of all modules and make sure, that
pins 14, the S– pin (LK 1000) or the Vo1– pins (LK 2000)
are also connected together. The load leads should have
equal length and cross section to ensure equal voltage
drops. Not more than 5 units should be connected in paral-
lel. If output voltage adjustment is requested we strongly
recommend to use the R-input instead of option P, as with
option P the required setting accuracy is difcult to achieve.
Fig. 31
An example of poor wiring for connection in parallel
Load
1
2
3
S+
Vo+
Vo–
S–
N
P
T
N
P
S+
Vo+
Vo–
S–
T
1
max. 5 units connected in parallel
11004
Fig. 32
Paralleling of double output units using option T with
Power bus.
Load
max. 5 units in parallel connection
+
–
Power bus
Module
Vo2–
Vo2+
Vo1–
Vo1+
T
Module
Vo2–
Vo2+
Vo1–
Vo1+
T
11037
The output voltages must be individually set prior to paral-
leling to within a tolerance of 1...2% or the R pins should be
connected together.
相關PDF資料 |
PDF描述 |
|---|---|
| LK1001-9PD3TB2 | 1-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE |
| LK1301-7ERD3B2 | 1-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE |
| LK1301-7PD6TB2 | 1-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE |
| LK1301-7PD7B2 | 1-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE |
| LK1301-7RDDB1 | 1-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LK1001-9ER | 制造商:Power-One 功能描述:ACDC - Bulk |
| LK100-24P | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Optoelectronic |
| LK100-28P | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Optoelectronic |
| LK10051R0K-T | 功能描述:固定電感器 INDCTR STD MULTILYR 0402 1uH 10% RoHS:否 制造商:AVX 電感:10 uH 容差:20 % 最大直流電流:1 A 最大直流電阻:0.075 Ohms 工作溫度范圍:- 40 C to + 85 C 自諧振頻率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接類型:SMD/SMT 封裝 / 箱體:6.6 mm x 4.45 mm |
| LK10051R0K-T | 制造商:TAIYO YUDEN 功能描述:Inductor Series:LF LK |
發布緊急采購，3分鐘左右您將得到回復。