- 您現在的位置：買賣IC網 > PDF目錄43982 > LK1001-7RD2TB2 1-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | LK1001-7RD2TB2 |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE |
| 封裝： | METAL, CASE K02, MODULE |
| 文件頁數： | 25/26頁 |
| 文件大?。?/td> | 601K |
| 代理商： | LK1001-7RD2TB2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁
Cassette Style
150 Watt AC-DC Converters
K Series
Edition 01/01.2001
8/26
Thermal Considerations
If a converter is located in free, quasi-stationary air (con-
vection cooling) at the indicated maximum ambient tem-
perature
TA max (see table: Temperature specifications) and
is operated at its nominal input voltage and output power,
the temperature measured at the
Measuring point of case
temperature TC (see: Mechanical Data) will approach the
indicated value
TC max after the warm-up phase. However,
the relationship between
TA and TC depends heavily on the
conditions of operation and integration into a system. The
thermal conditions are influenced by input voltage, output
current, airflow and temperature of surrounding compo-
nents and surfaces.
TA max is therefore, contrary to TC max,
an indicative value only.
Caution: The installer must ensure that under all operat-
ing conditions
TC remains within the limits stated in the
table:
Temperature specifications.
Notes: Sufficient forced cooling or an additional heat sink
allows
TA to be higher than 71
°C (e.g. 85°C) if T
C max is not
exceeded.
For -7 or -9 units at an ambient temperature
TA of 85°C with
only convection cooling, the maximum permissible current
for each output is approx. 40% of its nominal value as per
figure.
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
50
60
70
80
90
100
Io/Io nom
TA [°C]
0.9
1.0
Zwangsbelüftung
05089d
TA min
TC max
Konvektionskühlung
Fig. 7
Output current derating versus temperature for –7 and –9.
Thermal Protection
A temperature sensor generates an internal inhibit signal
which disables the outputs if the case temperature exceeds
TC max. The outputs are automatically re-enabled if the tem-
perature drops below this limit.
It is recommended that continuous operation under simul-
taneous extreme worst case conditions of the following
three parameters be avoided: Minimum input voltage,
maximum output power and maximum temperature.
Output Protection
Each output is protected against overvoltage which could
occur due to a failure of the control circuit by means of a
voltage suppressor diode which, under worst case condi-
tions, may become a short circuit. The suppressor diodes
are not designed to withstand externally applied over-
voltages. Overload at any of the two outputs will cause a
shut-down of both outputs. A red LED indicates the over-
load condition.
Uo1d
t d
Ur
t
Uo2d
<10
s
<10
s
Uo1
Uo2
Io1/Io1 nom
0
0.5
1
Io2/Io2 nom
05072
Fig. 8
Control deviation of uo1/2 d vs. dynamic load change.
Output Voltage Regulation of Single or Double Output
Modules with Outputs1 and 2 Connected in Series
Uo
Uo nom
0.98
0.5
0
0.5
1.0
Io1
IoL
Io
Io nom
05068
Fig. 9
Uo1 versus Io1 (typ.) of single output units
Parallel or Series Connection of Units
Single or double output units with equal nominal output volt-
age can be connected in parallel without any precautions
using option T.
With option T (current sharing), all units share the current
approximately equally.
Single output units and/or main and second outputs of dou-
ble output units can be connected in series with any other
(similar) output.
Note:
– Parallel connection of double output units should always
include both, main and second output to maintain good
regulation of both outputs.
– Not more than 5 units should be connected in parallel.
– Series connection of second outputs without involving
their main outputs should be avoided as regulation may
be poor.
– The maximum output current is limited by the output with
the lowest current limitation if several outputs are con-
nected in series.
相關PDF資料 |
PDF描述 |
|---|---|
| LK1301-9EPB2 | 1-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE |
| LK1301-9ERD1TB2 | 1-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE |
| LK1301-9ERD4TB2 | 1-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE |
| LK1301-9ERD6B2 | 1-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE |
| LK1301-9ERD8B2 | 1-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LK1001-9ER | 制造商:Power-One 功能描述:ACDC - Bulk |
| LK100-24P | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Optoelectronic |
| LK100-28P | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Optoelectronic |
| LK10051R0K-T | 功能描述:固定電感器 INDCTR STD MULTILYR 0402 1uH 10% RoHS:否 制造商:AVX 電感:10 uH 容差:20 % 最大直流電流:1 A 最大直流電阻:0.075 Ohms 工作溫度范圍:- 40 C to + 85 C 自諧振頻率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接類型:SMD/SMT 封裝 / 箱體:6.6 mm x 4.45 mm |
| LK10051R0K-T | 制造商:TAIYO YUDEN 功能描述:Inductor Series:LF LK |
發布緊急采購，3分鐘左右您將得到回復。