- 您現在的位置：買賣IC網 > PDF目錄369775 > LIS2L01 INERTIAL SENSOR: 2AXIS/1G LINEAR ACCELEROMETER PDF資料下載
參數資料
| 型號： | LIS2L01 |
| 元件分類： | 加速度傳感器 |
| 英文描述： | INERTIAL SENSOR: 2AXIS/1G LINEAR ACCELEROMETER |
| 中文描述： | 慣性傳感器：2AXIS/1G線性加速度計 |
| 文件頁數： | 4/6頁 |
| 文件大小： | 62K |
| 代理商： | LIS2L01 |
LIS2L01
4/6
Figure 1. Equivalent electrical circuit
1.2 IC Interface
The complete signal processing uses a fully differential structure, while the final stage converts the differential
signal into a single-ended to be compatible with the external world.
The first stage is a low-noise capacitive amplifier that implements a Correlated Double Sampling (CDS) at the
output to cancel the offset and the 1/f noise.
The signal is processed through a 2
nd
order low pass filter in order to reject out of band noise, the filter cut off
frequency is set to be 30Hz.
This filter is implemented using SC technique, which allows to realize a fully integrated system that avoid the
use of any external component.
The low noise input amplifier operates at 100 kHz while the two SC filters operate at 50 kHz sampling frequency.
This allows a large oversampling ratio, able to reduce in-band noise and to obtain an accurate output waveform.
The signal at the output of the SC filter is sampled and held using a different clock to avoid that the filter output
value during the CDS phase reaches the output pin.
All the analog parameter (output offset voltage and sensitivity) are ratiometric to the supply voltage. Increasing
or decreasing the supply voltage, the sensitivity and the offset will increase or decrease linearly. The feature
provides the cancellation of the error related to the supply voltage in the analog to digital conversion chain.
1.3 Factory calibration
In the IC interface different calibrations take place at factory level to provide to final user a device ready to be
used, the trimmed parameters are: gain, offset and cut off frequency of the SC filter.
The trimmed value are stored in the device with a poly-fuse technique. Any time the device is turned on the
memorized bits are loaded into the registers to be utilized during the normal operation. The poly-fuse approach
allow the final user to use the device without any need for further calibration.
C
s1x
C
s2x
C
ps1
C
ps2
C
pr
R
s2
R
s1
R
r
S1x
rot
S2x
C
s1y
C
s2y
C
ps1
C
ps2
C
pr
R
s2
R
s1
R
r
S1y
S2y
相關PDF資料 |
PDF描述 |
|---|---|
| LITECHIP | Microcontroller |
| LIU01FP | PCM Receiver |
| LIU01FQ | PCM Receiver |
| LIU01FS | PCM Receiver |
| LJ15-24P | Optoelectronic |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LIS2L02AL | 功能描述:加速計 - 板上安裝 2-axis +/-2g Linear MEMS Intertial Sensr RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
| LIS2L02AL_06 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:MEMS INERTIAL SENSOR:2-axis - +/-2g ultracompact linear accelerometer |
| LIS2L02ALTR | 功能描述:加速計 - 板上安裝 MEMS INERTIAL snsr 2 axis RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
| LIS2L02AO | 制造商:STMicroelectronics 功能描述:TWO-AXIS MEMS-BASED ACCELEROMETER - Bulk |
| LIS2L02AQ | 功能描述:ACCELEROMETER DUAL AXIS 44QFN RoHS:是 類別:傳感器，轉換器 >> 加速計 系列:- 標準包裝:1 系列:SCA1000 軸:X，Y 加速范圍:±1.7g 靈敏度:1.2V/g 電源電壓:4.75 V ~ 5.25 V 輸出類型:數字 帶寬:50±30Hz 接口:SPI 安裝類型:表面貼裝 封裝/外殼:12-SMD 供應商設備封裝:12-SMD 其它名稱:551-1007-1 |
發布緊急采購，3分鐘左右您將得到回復。