參數資料
型號： LH28F800SUTD
英文描述： x8/x16 Flash EEPROM
中文描述： x8/x16閃存EEPROM
文件頁數： 23/56頁
文件大?。?/td> 373K
代理商： LH28F800SUTD
LH28F160S5-L/S5H-L
- 23 -
Table 13.1 Status Register Definition
ECBLBS
WSBLBS
5
4
WSMS
7
BESS
6
VPPS
3
WSS
2
DPS
1
R
0
SR.7 = WRITE STATE MACHINE STATUS (WSMS)
1 = Ready
0 = Busy
SR.6 = BLOCK ERASE SUSPEND STATUS (BESS)
1 = Block Erase Suspended
0 = Block Erase in Progress/Completed
SR.5 =
ERASE AND CLEAR BLOCK LOCK-BITS STATUS
(ECBLBS)
1 = Error in Erase or Clear Block Lock-Bits
0 = Successful Erase or Clear Block Lock-Bits
SR.4 =
WRITE AND SET BLOCK LOCK-BIT STATUS
(WSBLBS)
1 = Error in Write or Set Block Lock-Bit
0 = Successful Write or Set Block Lock-Bit
SR.3 = V
PP
STATUS (VPPS)
1 = V
PP
Low Detect, Operation Abort
0 = V
PP
OK
SR.2 = WRITE SUSPEND STATUS (WSS)
1 = Write Suspended
0 = Write in Progress/Completed
SR.1 = DEVICE PROTECT STATUS (DPS)
1 = Block Lock-Bit and/or WP# Lock Detected,
Operation Abort
0 = Unlock
SR.0 =
RESERVED FOR FUTURE ENHANCEMENTS (R)
NOTES :
Check STS or SR.7 to determine block erase, full chip erase,
(multi) word/byte write or block lock-bit configuration
completion.
SR.6-0 are invalid while SR.7 = "0".
If both SR.5 and SR.4 are "1"s after a block erase, full chip
erase, (multi) word/byte write, block lock-bit configuration or
STS configuration attempt, an improper command sequence
was entered.
SR.3 does not provide a continuous indication of V
PP
level.
The WSM interrogates and indicates the V
PP
level only after
block erase, full chip erase, (multi) word/byte write or block
lock-bit configuration command sequences. SR.3 is not
guaranteed to reports accurate feedback only when V
PP
≠
V
PPH1
.
SR.1 does not provide a continuous indication of block lock-bit
values. The WSM interrogates block lock-bit, and WP# only
after block erase, full chip erase, (multi) word/byte write or
block lock-bit configuration command sequences. It informs
the system, depending on the attempted operation, if the block
lock-bit is set and/or WP# is not V
IH
. Reading the block lock
configuration codes after writing the Read Identifier Codes
command indicates block lock-bit status.
SR.0 is reserved for future use and should be masked out
when polling the status register.
Table 13.2 Extended Status Register Definition
R
R
5
4
SMS
7
R
6
R
3
R
2
R
1
R
0
XSR.7 = STATE MACHINE STATUS (SMS)
1 = Multi Word/Byte Write available
0 = Multi Word/Byte Write not available
XSR.6-0 =
RESERVED FOR FUTURE ENHANCEMENTS (R)
NOTES :
After issue a Multi Word/Byte Write command : XSR.7
indicates that a next Multi Word/Byte Write command is
available.
XSR.6-0 are reserved for future use and should be masked
out when polling the extended status register.
相關PDF資料
PDF描述
LH28F400BGE-BL12 x16 Flash EEPROM
LH28F400BGE-BL85 x16 Flash EEPROM
LH28F400BGE-TL12 x16 Flash EEPROM
LH28F400BGE-TL85 x16 Flash EEPROM
LH28F400BGHB-BL12 x16 Flash EEPROM
相關代理商/技術參數
參數描述
LH28FOO8SAHR-85 制造商:SHARP 制造商全稱:Sharp Electrionic Components 功能描述:8 MBIT(1 MBIT x 8)FLASH MEMORY
LH-2A-240 制造商:Line Electric 功能描述:
LH2H-F-DHK 功能描述:控制器 TIME COUNTER 4D99HRS NO VOLT IN RoHS:否 制造商:Omron Industrial 模擬/數字:Digital 類型:Digital Temperature Controller 顯示器類型:11-Segment, 4 Digit 電源電壓:100 VAC to 240 VAC 安裝: 控制方法: 大小:48 mm x 48 mm
LH2H-F-DHK-DL 功能描述:控制器 TIME COUNTER 4D99HRS DC INPUT RoHS:否 制造商:Omron Industrial 模擬/數字:Digital 類型:Digital Temperature Controller 顯示器類型:11-Segment, 4 Digit 電源電壓:100 VAC to 240 VAC 安裝: 控制方法: 大小:48 mm x 48 mm
LH2H-F-DHK-DL-B 功能描述:計時器 TIME COUNTER 4D99HR DC IN W/BCKL RoHS:否 制造商:Omron Industrial 定時范圍:0.05 s to 30 hr 電源電壓:100 VAC to 240 VAC 系列:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*