- 您現在的位置：買賣IC網 > PDF目錄358792 > LH28F800BGHRTL85 (Sharp Corporation) RES CURRENT SENSE .025 OHM 1W 1% PDF資料下載
參數資料
| 型號： | LH28F800BGHRTL85 |
| 廠商： | Sharp Corporation |
| 英文描述： | RES CURRENT SENSE .025 OHM 1W 1% |
| 中文描述： | 8 M位（512 KB的× 16）SmartVoltage閃存 |
| 文件頁數： | 4/38頁 |
| 文件大?。?/td> | 328K |
| 代理商： | LH28F800BGHRTL85 |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
LH28F800SU
8M (512K × 16, 1M × 8) Flash Memory
4
PIN DESCRIPTION
SYMBOL
TYPE
NAME AND FUNCTION
A
0
INPUT
BYTE-SELECT ADDRESS:
Selects between high and low byte when device is in x8
mode. This address is latched in x8 Data Writes. Not used in x16 mode (i.e., the
A
0
input buffer is turned off when BYTE is high).
WORD-SELECT ADDRESSES:
Select a word within one 64K block. A
6
- A
15
selects
1 of 1024 rows, and A
1
- A
5
selects 16 of 512 columns. These addresses are
latched during Data Writes.
A
1
- A
15
INPUT
A
16
- A
19
INPUT
BLOCK-SELECT ADDRESSES:
Select 1 of 16 Erase blocks. These addresses are
latched during Data Writes, Erase and Lock-Block operations.
DQ
0
- DQ
7
INPUT/OUTPUT
LOW-BYTE DATA BUS:
Inputs data and commands during CUI write cycles.
Outputs array, buffer, identifier or status data in the appropriate Read mode. Floated
when the chip is de-selected or the outputs are disabled.
DQ
8
- DQ
15
INPUT/OUTPUT
HIGH-BYTE DATA BUS
: Inputs data during x16 Data-Write operations. Outputs
array, buffer or identifier data in the appropriate Read mode; not used for Status
register reads. Floated when the chip is de-selected or the outputs are disabled.
CE
0
, CE
1
INPUT
CHIP ENABLE INPUTS
: Activate the device’s control logic, input buffers, decoders and
sense amplifiers. With either CE
0
or CE
1
high, the device is de-selected and power
consumption reduces to Standby levels upon completion of any current Data-Write or
Erase operations. Both CE
0
, CE
1
must be low to select the device. All timing
specifications are the same for both signals. Device Selection occurs with the latter
falling edge of CE
0
or CE
1
. The first rising edge of CE
0
or CE
1
disables the device.
RESET/POWER-DOWN:
With RP
low, the device is reset, any current operation is
aborted and device is put into the deep power down mode. When the power is turned
on, RP
pin is turned to low in order to return the device to default configuration. When
the 3/5
pin is switched, or when the power transition is occurred, or at the power on/off,
RP
is required to stay low in order to protect data from noise. When returning from
Deep Power-Down, a recovery time of 400 ns (V
CC
+5.0 V ±0.25 V) is required to allow
these circuits to power-up. When RP
goes low, any current or pending WSM
operation(s) are terminated, and the device is reset. All Status registers return to ready
(with all status flags cleared). After returning, the device is in read array mode.
RP
INPUT
OE
INPUT
OUTPUT ENABLE:
Gates device data through the output buffers when low. The
outputs float to tri-state off when OE
is high.
NOTE:
CE
X
overrides OE
, and OE
overrides WE.
WRITE ENABLE:
Controls access to the CUI, Page Buffers, Data Queue Registers
and Address Queue Latches. WE is active low, and latches both address and data
(command or array) on its rising edge.
WE
INPUT
RY
/BY
OPEN DRAIN
OUTPUT
READY/BUSY:
Indicates status of the internal WSM. When low, it indicates that the
WSM is busy performing an operation. RY
/BY
high indicates that the WSM is ready
for new operations (or WSM has completed all pending operations), or Erase is
Suspended, or the device is in deep power-down mode. This output is always active
(i.e., not floated to tri-state off when OE
or CE
0
, CE
1
are high), except if a RY
/BY
Pin Disable command is issued.
相關PDF資料 |
PDF描述 |
|---|---|
| LH28F800BGRTL12 | 8 M-bit (512 kB x 16) SmartVoltage Flash Memories |
| LH28F800BGRTL85 | 8 M-bit (512 kB x 16) SmartVoltage Flash Memories |
| LH28F800BVE-BTL90 | 8M Flash Memory |
| LH28F800BVE-TTL90 | 8M Flash Memory |
| LH28F800SU | 8M (512K 】 16, 1M 】 8) Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LH28F800BGHR-TL85 | 制造商:SHARP 制造商全稱:Sharp Electrionic Components 功能描述:8 M-bit (512 kB x 16) SmartVoltage Flash Memories |
| LH28F800BG-L | 制造商:SHARP 制造商全稱:Sharp Electrionic Components 功能描述:8 M-bit (512 kB x 16) SmartVoltage Flash Memories |
| LH28F800BGN-BL12 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x16 Flash EEPROM |
| LH28F800BGN-BL85 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x16 Flash EEPROM |
| LH28F800BGN-TL12 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x16 Flash EEPROM |
發布緊急采購，3分鐘左右您將得到回復。