- 您現在的位置：買賣IC網 > PDF目錄358792 > LH28F400SUHT-NC80 (Sharp Corporation) 4Mbit(512Kbit x 8,256 Kbit x 16) 5V Single Voltage Flash Memory PDF資料下載
參數資料
| 型號： | LH28F400SUHT-NC80 |
| 廠商： | Sharp Corporation |
| 英文描述： | 4Mbit(512Kbit x 8,256 Kbit x 16) 5V Single Voltage Flash Memory |
| 中文描述： | 的4Mb（512Kbit x 8256千位× 16）5V單電壓閃存 |
| 文件頁數： | 16/35頁 |
| 文件大小： | 294K |
| 代理商： | LH28F400SUHT-NC80 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
LH28F400SU-NC
4M (512K × 8, 256K × 16) Flash Memory
16
Figure 12. Erase All Unlocked Blocks with Compatible Status Registers
28F400SUT-NC60-10
START
(NOTE)
BUS
OPERATION
COMMAND
COMMENTS
WRITE A7H
CSR.7 =
0
YES
NO
1
0
1
0
1
CSR FULL STATUS
CHECK IF DESIRED
OPERATION
COMPLETE
WRITE D0H
CLEAR CSRD
RETRY/ERROR
RECOVERY
(NOTE)
ERASE
SUCCESSFUL
V
PP
LOW
DETECT
READ CSRD
(see above)
SUSPEND
ERASE
SUSPEND
ERASE LOOP
CSR.4, 5 =
CSR.3 =
Write
Write
Read
Standby
Erase All
Unlocked
Blocks
Confirm
D = A7H
A = X
D = D0H
A = X
Q = CSRD
Toggle CE or OE
to update CSRD
A = X
CSR Full Status Check can be done after Erase All Unlocked
Block, or after a sequence of Erasures.
Write FFH after the last operation to reset
device to read array mode.
See Command Bus Cycle notes for description of codes.
NOTE:
Where power off or RP is set low during erase operation,
1. Clear CSR.3/4/5 and issue Reset WP command,
2. Retry Erase All Unlocked Block Erase command to
erase all blocks, or issue Single Block Erase to
erase all of the unlocked blocks in sequence.
3. Set WP command is issued, if necessary.
Check CSR.7
1 = WSM Ready
0 = WSM Busy
BUS
OPERATION
COMMAND
CSR FULL STATUS CHECK PROCEDURE
COMMENTS
Standby
Standby
Check CSR.4, 5
1 = Erase Error
0 = Erase Successful
Both 1 = Command
Sequence Error
CSR.3, 4, 5 should be cleared, if set, before further attempts
are initiated.
NOTE:
If CSR.3 (VPPS) is set to '1', after clearing CSR.3/4/5,
1. Issue Reset WP command,
2. Retry Erase All Unlocked Block Erase command to erase
all blocks, or issue Single Block Erase to erase all of the
unlocked blocks in sequence.
3. Set WP command is issued, if necessary.
If CSR.3 (VPPS) is set to '0', after clearing CSR.3/4/5,
1. Retry Erase All Unlocked Block Erase command.
READ COMPATIBLE
STATUS REGISTER
Check CSR.3
1 = V
PP
Low Detect
0 = V
PP
OK
相關PDF資料 |
PDF描述 |
|---|---|
| LH28F400SUHE-NC80 | 4Mbit(512Kbit x 8, 256 Kbit x 16) 5V Single Voltage Flash Memory |
| LH28F400BVHE-BL85 | 4M Flash Memory |
| LH28F400SUB-Z0 | 4M (512K 】 8, 256K 】 16) Flash Memory |
| LH28F400BG | 4M-BIT(256KBx16) SmartVoltage Flash MEMORY |
| LH28F400SU | 4Mbit(512Kbit x 8, 256 Kbit x 16) 5V Single Voltage Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LH28F400SU-LC | 制造商:SHARP 制造商全稱:Sharp Electrionic Components 功能描述:4M (512K 】 8, 256K 】 16) Flash Memory |
| LH28F400SUN | 制造商:SHARP 制造商全稱:Sharp Electrionic Components 功能描述:4Mbit(512Kbit x 8,256Kbit x 16) 3.3V Flash Memory |
| LH28F400SU-NC | 制造商:SHARP 制造商全稱:Sharp Electrionic Components 功能描述:4M (512K 】 8, 256K 】 16) Flash Memory |
| LH28F400SUN-LC12 | 制造商:SHARP 制造商全稱:Sharp Electrionic Components 功能描述:4Mbit(512Kbit x 8,256Kbit x 16) 3.3V Flash Memory |
| LH28F400SUN-LC15 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8/x16 Flash EEPROM |
發布緊急采購，3分鐘左右您將得到回復。