參數資料
型號： LH28F008SCHB-TL12
英文描述： x8 Flash EEPROM
中文描述： x8閃存EEPROM的
文件頁數： 13/56頁
文件大?。?/td> 373K
代理商： LH28F008SCHB-TL12
- 13 -
LH28F160S5-L/S5H-L
4.1
Upon initial device power-up and after exit from
deep power-down mode, the device defaults to
read array mode. This operation is also initiated by
writing the Read Array command. The device
remains enabled for reads until another command
is written. Once the internal WSM has started a
block erase, full chip erase, (multi) word/byte write
or block lock-bit configuration, the device will not
recognize the Read Array command until the WSM
completes its operation unless the WSM is
suspended via an Erase Suspend and (Multi)
Word/Byte Write Suspend command. The Read
Array command functions independently of the V
PP
voltage and RP# must be V
IH
.
Read Array Command
4.2
The identifier code operation is initiated by writing
the Read Identifier Codes command. Following the
command write, read cycles from addresses shown
in
Fig. 2
retrieve the manufacture, device, block
lock configuration and block erase status (see
Table 4
for identifier code values). To terminate the
operation, write another valid command. Like the
Read Array command, the Read Identifier Codes
command functions independently of the V
PP
voltage and RP# must be V
IH
. Following the Read
Identifier Codes command, the following information
can be read :
Read Identifier Codes Command
Table 4 Identifier Codes
CODE
NOTE :
1.
X selects the specific block status code to be read. See
Fig. 2
for the device identifier code memory map.
4.3
The status register may be read to determine when
a block erase, full chip erase, (multi) word/byte
write or block lock-bit configuration is complete and
whether the operation completed successfully (see
Table 13.1
). It may be read at any time by writing
the Read Status Register command. After writing
this command, all subsequent read operations
output data from the status register until another
valid command is written. The status register
contents are latched on the falling edge of OE# or
CE# (Either CE
0
# or CE
1
#), whichever occurs. OE#
or CE# (Either CE
0
# or CE
1
#) must toggle to V
IH
before further reads to update the status register
latch. The Read Status Register command
functions independently of the V
PP
voltage. RP#
must be V
IH
.
Read Status Register Command
The extended status register may be read to
determine multi byte write availability (see
Table
13.2
). The extended status register may be read at
any time by writing the Multi Byte Write command.
After writing this command, all subsequent read
operations output data from the extended status
register, until another valid command is written. The
contents of the extended status register are latched
on the falling edge of OE# or CE# (Either CE
0
# or
CE
1
#), whichever occurs last in the read cycle.
Multi Byte Write command must be re-issued to
update the extended status register latch.
4.4
Status register bits SR.5, SR.4, SR.3 and SR.1 are
set to "1"s by the WSM and can only be reset by
the Clear Status Register command. These bits
indicate various failure conditions (see
Table 13.1
).
By allowing system software to reset these bits,
several operations (such as cumulatively erasing or
locking multiple blocks or writing several bytes in
Clear Status Register Command
ADDRESS
00000H
00001H
00002H
00003H
X0004H
(NOTE 1)
X0005H
(NOTE 1)
DATA
Manufacture Code
B0
Device Code
D0
Block Status Code
Block is Unlocked
Block is Locked
Last erase operation
completed successfully
Last erase operation did
not completed successfully
Reserved for Future Use
DQ
0
= 0
DQ
0
= 1
DQ
1
= 0
DQ
1
= 1
DQ
2-7
相關PDF資料
PDF描述
LH28F008SCHB-TL15 x8 Flash EEPROM
LH28F008SCHB-V12 x8 Flash EEPROM
LH28F008SCHB-V85 x8 Flash EEPROM
LH28F008SCHN-12 x8 Flash EEPROM
LH28F008SCHN-85 x8 Flash EEPROM
相關代理商/技術參數
參數描述
LH28F008SCHB-TL15 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 Flash EEPROM
LH28F008SCHB-V12 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 Flash EEPROM
LH28F008SCHB-V85 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 Flash EEPROM
LH28F008SCH-L 制造商:SHARP 制造商全稱:Sharp Electrionic Components 功能描述:8-MBIT(1 MB x 8) SmartVoltage Flash MEMORY
LH28F008SCHN-12 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 Flash EEPROM
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*