- 您現在的位置：買賣IC網 > PDF目錄39203 > LEN-1.5/28-D12H (MURATA POWER SOLUTIONS INC) 1-OUTPUT DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | LEN-1.5/28-D12H |
| 廠商： | MURATA POWER SOLUTIONS INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 文件頁數： | 5/10頁 |
| 文件大?。?/td> | 355K |
| 代理商： | LEN-1.5/28-D12H |
MDC_LEN D12 Models.B01 Page 4 of 10
Technical enquiries email: sales@murata-ps.com, tel: +1 508 339 3000
www.murata-ps.com
LEN-D12 Models
Non-Isolated, 28A Eighth Brick
DC/DC Converters
Output ripple/noise (also referred to as periodic and random deviations or
PARD) may be reduced below specied limits with the installation of additional
external output capacitors. Output capacitors function as true lter elements
and should be selected for bulk capacitance, low ESR, and appropriate fre-
quency response. Any scope measurements of PARD should be made directly
at the DC/DC output pins with scope probe ground less than 0.5" in length.
All external capacitors should have appropriate voltage ratings and be
located as close to the converters as possible. Temperature variations for all
relevant parameters should be taken into consideration.
The most effective combination of external I/O capacitors will be a func-
tion of your line voltage and source impedance, as well as your particular load
and layout conditions. Our Applications Engineers can recommend potential
solutions and discuss the possibility of our modifying a given device’s internal
ltering to meet your specic requirements. Contact our Applications Engineer-
ing Group for additional details.
Input Fusing
Most applications and or safety agencies require the installation of fuses at the
inputs of power conversion components. LEN D12 Series DC/DC converters are
not internally fused. Therefore, input fusing is mandatory for safety reasons, and
safety agencies require a time delay fuse with a value no greater than 40 Amps,
which should be installed within the ungrounded input path to the converter.
As a rule of thumb however, we recommend to use a normal-blow or
slow-blow fuse with a typical value of about twice the maximum input current,
calculated at low line with the converters minimum efciency.
Safety Considerations
LEN D12's are non-isolated DC/DC converters. In general, all DC/DC's must
be installed, including considerations for I/O voltages and spacing/separation
requirements, in compliance with relevant safety-agency specications (usually
UL/IEC/EN60950-1).
In particular, for a non-isolated converter's output voltage to meet SELV
(safety extra low voltage) requirements, its input must be SELV compliant. If the
output needs to be ELV (extra low voltage), the input must be ELV.
Start-Up Time
The VIN to VOUT Start-Up Time is the interval between the time at which a ramp-
ing input voltage crosses the lower limit of the specied input voltage range
(10.2 Volts) and the fully loaded output voltage enters and remains within its
specied accuracy band. Actual measured times will vary with input source
impedance, external input capacitance, and the slew rate and nal value of the
input voltage as it appears to the converter.
The On/Off to VOUT Start-Up Time assumes the converter is turned off via the
On/Off Control with the nominal input voltage already applied to the converter.
The specication denes the interval between the time at which the converter
is turned on and the fully loaded output voltage enters and remains within its
specied accuracy band. See Typical Performance Curves.
Remote Sense
LEN D12 Series DC/DC converters offer an output sense function on pin 10.
The sense function enables point-of-use regulation for overcoming moderate
IR drops in conductors and/or cabling. Since these are non-isolated devices
whose inputs and outputs usually share the same ground plane, sense is
provided only for the +Output.
The remote sense line is part of the feedback control loop regulating the
DC/DC converter’s output. The sense line carries very little current and conse-
quently requires a minimal cross-sectional-area conductor. As such, it is not
a low-impedance point and must be treated with care in layout and cabling.
Sense lines should be run adjacent to signals (preferably ground), and in cable
and/or discrete-wiring applications, twisted-pair or similar techniques should be
used. To prevent high frequency voltage differences between VOUT and Sense,
we recommend installation of a 1000pF capacitor close to the converter.
The sense function is capable of compensating for voltage drops between
the +Output and +Sense pins that do not exceed 10% of VOUT.
[VOUT(+) – Common] – [Sense(+) – Common]
≤ 10%VOUT
Power derating (output current limiting) is based upon maximum output cur-
rent and voltage at the converter's output pins. Use of trim and sense functions
can cause the output voltage to increase, thereby increasing output power
beyond the converter's specied rating. Therefore:
(VOUT at pins) x (IOUT)
≤ rated output power
The internal 10.5
Ω resistor between +Sense and +Output (see Figure 1)
serves to protect the sense function by limiting the output current owing
through the sense line if the main output is disconnected. It also prevents
output voltage runaway if the sense connection is disconnected.
Note: If devices have the +Sense pin (pin 10) installed (no part-number
sufx) and the sense function is not used for remote regulation, +Sense
(pin 10) must be tied to +Output (pin 7, 9) at the DC/DC converter pins.
On/Off Control
The On/Off Control pin may be used for remote on/off operation. LEN D12
Series DC/DC converters are designed so that they are enabled when the
control pin is left open (or pulled low to 0 to +0.4V) and disabled when the
control pin is pulled high (+2.8V to +VIN). As shown in Figure 2, all models have
an internal 20k
Ω pull-down resistor to Common (ground).
相關PDF資料 |
PDF描述 |
|---|---|
| LES008ZD-2N9 | 1-OUTPUT 15 W DC-DC REG PWR SUPPLY MODULE |
| LES010ZE-1N9 | 1-OUTPUT 15 W DC-DC REG PWR SUPPLY MODULE |
| LES015YG-3N2H | 1-OUTPUT 15 W DC-DC REG PWR SUPPLY MODULE |
| LES015YHN3H | 1-OUTPUT 15 W DC-DC REG PWR SUPPLY MODULE |
| LES015YJ-3N3V | 1-OUTPUT 15 W DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LEN-2.5/28-D12 | 功能描述:DC/DC轉換器 70W 12V to 2.5V 28A RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| LEN-2.5/28-D12B-C | 功能描述:DC/DC轉換器 70W 12V to 2.5V 28A RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| LEN-2.5/28-D12-C | 功能描述:DC/DC轉換器 70W 12V to 2.5V 28A RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| LEN-2.5/28-D12H-C | 功能描述:DC/DC轉換器 70W 12V to 2.5V 28A HEAT SINK RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| LEN-2.5/28-D12M | 制造商:Murata Power Solutions 功能描述:Module DC-DC 1-OUT 2.5V 28A 10-Pin 1/8-Brick |
發布緊急采購，3分鐘左右您將得到回復。