- 您現在的位置：買賣IC網 > PDF目錄377620 > LCQF (Linear Technology Corporation) 20mA LED Driver and OLED Driver with Integrated Schottky in 3mm x 2mm DFN PDF資料下載
參數資料
| 型號： | LCQF |
| 廠商： | Linear Technology Corporation |
| 英文描述： | 20mA LED Driver and OLED Driver with Integrated Schottky in 3mm x 2mm DFN |
| 中文描述： | 20mA的LED驅動器和3毫米的OLED驅動器集成肖特基x 2mm DFN封裝 |
| 文件頁數： | 8/24頁 |
| 文件大小： | 449K |
| 代理商： | LCQF |
LT3498
8
3498f
OPERATION—LED DRIVER
The LED portion of the LT3498 uses a constant-frequency,
current mode control scheme to provide excellent line
and load regulation. Operation can be best understood
by referring to the Block Diagram.
At power-up, the capacitor at the CAP1 pin is charged up
to V
IN
(input supply voltage) through the inductor and the
internal Schottky diode. If CTRL1 is pulled higher than
125mV, the bandgap reference, the start-up bias and the
oscillator are turned on. At the start of each oscillator cycle,
the power switch Q1 is turned on. A voltage proportional
to the switch current is added to a stabilizing ramp and the
resulting sum is fed into the positive terminal of the PWM
comparator, A2. When this voltage exceeds the level at the
negative input of A2, the PWM logic turns off the power
switch. The level at the negative input of A2 is set by the
error amplifier A1, and is simply an amplified version of
the difference between the V
CAP1
and V
LED1
voltage and
the bandgap reference. In this manner the error amplifier,
A1, sets the correct peak current level in inductor L1 to
keep the output in regulation. The CTRL1 pin is used to
adjust the LED current. The LED Driver is shutdown when
CTRL1 is pulled lower than 75mV.
Minimum Output Current
The LED Driver of the LT3498 can drive a 4-LED string at
2mA LED current, without pulse-skipping, using the same
external components shown in the application circuit on
the front page of this data sheet. As current is further
reduced, the device will begin skipping pulses. This will
result in some low frequency ripple, although the average
LED current remains regulated down to zero. The photo in
Figure 1 details circuit operation driving four white LEDs
at 2mA load. Peak inductor current is less than 60mA and
the regulator operates in discontinuous mode, meaning
the inductor current reaches zero during the discharge
phase. After the inductor current reaches zero, the SW1
pin exhibits ringing due to the LC tank circuit formed
by the inductor in combination with the switch and the
diode capacitance. This ringing is not harmful; far less
spectral energy is contained in the ringing than in the
switch transitions.
200
ns
/DIV
V
W
10V/DIV
I
L
50mA/DIV
349
8
F01
V
IN
= 4.2V
I
= 2mA
4 LED
s
Figure 1. Switching Waveforms with
Four White LEDs at 2mA Load
相關PDF資料 |
PDF描述 |
|---|---|
| LCXW | 1.1A, Low Noise, Low Dropout Linear Regulator |
| LD1408 | 8-Bit Multiplying D/A Converter |
| LD1508 | 8-Bit Multiplying D/A Converter |
| LD2114A-4 | RAM FAMIRLY EXPRESS |
| LD2114A-5 | RAM FAMIRLY EXPRESS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LCQT-MSOP10 | 功能描述:IC Socket Adapter MSOP To DIP, 0.3" (7.62mm) Row Spacing Through Hole 制造商:aries electronics 系列:Correct-A-Chip? 零件狀態:有效 轉換自（適配器端）:MSOP 轉換至（適配器端）:DIP，0.3"（7.62mm）行距 引腳數:10 間距 - 配接:0.020"（0.50mm） 觸頭表面處理 - 配接:- 安裝類型:通孔 端接:焊接 間距 - 柱:0.100"（2.54mm） 觸頭表面處理 - 柱:金 外殼材料:聚酯 板材料:FR4 環氧玻璃 端接柱長度:0.236"（6.00mm） 材料可燃性等級:UL94 V-0 特性:- 額定電流:- 工作溫度:-55°C ~ 125°C 觸頭材料 - 配接:- 觸頭材料 - 柱:黃銅 觸頭表面處理厚度 - 配接:- 觸頭表面處理厚度 - 柱:閃存 標準包裝:48 |
| LCQT-QFP0.5-32 | 功能描述:IC Socket Adapter Multiple Packages To QFP Through Hole 制造商:aries electronics 系列:Correct-A-Chip? 零件狀態:有效 轉換自（適配器端）:多封裝 轉換至（適配器端）:QFP 引腳數:32 間距 - 配接:0.020"（0.50mm） 觸頭表面處理 - 配接:- 安裝類型:通孔 端接:焊接 間距 - 柱:0.100"（2.54mm） 觸頭表面處理 - 柱:金 外殼材料:聚酯 板材料:FR4 環氧玻璃 端接柱長度:0.236"（6.00mm） 材料可燃性等級:UL94 V-0 特性:- 額定電流:- 工作溫度:-55°C ~ 125°C 觸頭材料 - 配接:- 觸頭材料 - 柱:黃銅 觸頭表面處理厚度 - 配接:- 觸頭表面處理厚度 - 柱:閃存 標準包裝:17 |
| LCQT-QFP0.5-40 | 功能描述:IC Socket Adapter Multiple Packages To QFP Through Hole 制造商:aries electronics 系列:Correct-A-Chip? 零件狀態:有效 轉換自（適配器端）:多封裝 轉換至（適配器端）:QFP 引腳數:40 間距 - 配接:0.020"（0.50mm） 觸頭表面處理 - 配接:- 安裝類型:通孔 端接:焊接 間距 - 柱:0.100"（2.54mm） 觸頭表面處理 - 柱:金 外殼材料:聚酯 板材料:FR4 環氧玻璃 端接柱長度:0.236"（6.00mm） 材料可燃性等級:UL94 V-0 特性:- 額定電流:- 工作溫度:-55°C ~ 125°C 觸頭材料 - 配接:- 觸頭材料 - 柱:黃銅 觸頭表面處理厚度 - 配接:- 觸頭表面處理厚度 - 柱:閃存 標準包裝:17 |
| LCQT-QFP0.5-40-1 | 功能描述:IC Socket Adapter Multiple Packages To QFP Through Hole 制造商:aries electronics 系列:Correct-A-Chip? 零件狀態:有效 轉換自（適配器端）:多封裝 轉換至（適配器端）:QFP 引腳數:40 間距 - 配接:0.020"（0.50mm） 觸頭表面處理 - 配接:- 安裝類型:通孔 端接:焊接 間距 - 柱:0.100"（2.54mm） 觸頭表面處理 - 柱:金 外殼材料:聚酯 板材料:FR4 環氧玻璃 端接柱長度:0.236"（6.00mm） 材料可燃性等級:UL94 V-0 特性:- 額定電流:- 工作溫度:-55°C ~ 125°C 觸頭材料 - 配接:- 觸頭材料 - 柱:黃銅 觸頭表面處理厚度 - 配接:- 觸頭表面處理厚度 - 柱:閃存 標準包裝:17 |
| LCQT-QFP0.5-52 | 功能描述:IC Socket Adapter Multiple Packages To QFP Through Hole 制造商:aries electronics 系列:Correct-A-Chip? 零件狀態:有效 轉換自（適配器端）:多封裝 轉換至（適配器端）:QFP 引腳數:52 間距 - 配接:0.020"（0.50mm） 觸頭表面處理 - 配接:- 安裝類型:通孔 端接:焊接 間距 - 柱:0.100"（2.54mm） 觸頭表面處理 - 柱:金 外殼材料:聚酯 板材料:FR4 環氧玻璃 端接柱長度:0.236"（6.00mm） 材料可燃性等級:UL94 V-0 特性:- 額定電流:- 工作溫度:-55°C ~ 125°C 觸頭材料 - 配接:- 觸頭材料 - 柱:黃銅 觸頭表面處理厚度 - 配接:- 觸頭表面處理厚度 - 柱:閃存 標準包裝:17 |
發布緊急采購，3分鐘左右您將得到回復。