- 您現在的位置：買賣IC網 > PDF目錄383255 > LCP152 (意法半導體) Programmable transient voltage suppressor for SLIC protection PDF資料下載
參數資料
| 型號： | LCP152 |
| 廠商： | 意法半導體 |
| 英文描述： | Programmable transient voltage suppressor for SLIC protection |
| 中文描述： | 可編程的用戶接口保護瞬態電壓抑制器 |
| 文件頁數： | 6/11頁 |
| 文件大小： | 154K |
| 代理商： | LCP152 |
Technical information
LCP1521S/LCP152DEE
6/11
2
Technical information
Figure 5.
LCP152 concept behavior
Figure 5.
shows the classical protection circuit using the LCP152 crowbar concept. This
topology has been developed to protect the new high voltage SLICs. It allows to program the
negative firing threshold while the positive clamping value is fixed at GND.
When a negative surge occurs on one wire (L1 for example) a current IG flows through the
base of the transistor T1 and then injects a current in the gate of the thyristor Th1. Th1 fires
and all the surge current flows through the ground. After the surge when the current flowing
through Th1 becomes less negative than the holding current IH, then Th1 switches off.
When a positive surge occurs on one wire (L1 for example) the diode D1 conducts and the
surge current flows through the ground.
Figure 6.
Example of PCB layout based on LCP152S protection
Figure 6.
shows the classical PCB layout used to optimize line protection.
The capacitor C is used to speed up the crowbar structure firing during the fast surge edges.
This allows to minimize the dynamical breakover voltage at the SLIC Tip and Ring inputs
during fast strikes. Note that this capacitor is generally present around the SLIC - Vbat pin.
So to be efficient it has to be as close as possible from the LCP152 Gate pin and from the
reference ground track (or plan) (see
Figure 6.
). The optimized value for C is 220 nF.
The series resitors Rs1 and Rs2 designed in
Figure 5.
represent the fuse resistors or the
PTC which are mandatory to withstand the power contact or the power induction tests
V
Ring
GND
Gate
TIP
RING
GND
-Vbat
C
Rs1
Rs2
L 1
L 2
VTip
Th1
D1
T1
IG
ID1
To
line side
2
GND
To
SLIC side
LCP1521S
相關PDF資料 |
PDF描述 |
|---|---|
| LCP3121 | OVERVOLTAGE AND OVERCURRENT PROTECTION FOR TELECOM LINE |
| LD1084D2M90 | 5.0 AMP POSITIVE VOLTAGE REGULATOR |
| LD1084D2T90 | 5.0 AMP POSITIVE VOLTAGE REGULATOR |
| LD1084V120 | 5.0 AMP POSITIVE VOLTAGE REGULATOR |
| LD1084V15 | 5.0 AMP POSITIVE VOLTAGE REGULATOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LCP1521 | 功能描述:ESD 抑制器 Dual Program TVS RoHS:否 制造商:STMicroelectronics 通道:8 Channels 擊穿電壓:8 V 電容:45 pF 端接類型:SMD/SMT 封裝 / 箱體:uQFN-16 功率耗散 Pd: 工作溫度范圍:- 40 C to + 85 C |
| LCP1521RL | 功能描述:ESD 抑制器 Dual Program TVS RoHS:否 制造商:STMicroelectronics 通道:8 Channels 擊穿電壓:8 V 電容:45 pF 端接類型:SMD/SMT 封裝 / 箱體:uQFN-16 功率耗散 Pd: 工作溫度范圍:- 40 C to + 85 C |
| LCP1521S | 功能描述:TVS 二極管 - 瞬態電壓抑制器 SLIC Protection IC RoHS:否 制造商:Vishay Semiconductors 極性:Bidirectional 工作電壓: 擊穿電壓:58.9 V 鉗位電壓:77.4 V 峰值浪涌電流:38.8 A 系列: 封裝 / 箱體:DO-214AB 最小工作溫度:- 55 C 最大工作溫度:+ 150 C |
| LCP1521S_06 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Programmable transient voltage suppressor for SLIC protection |
| LCP1521SRL | 功能描述:ESD 抑制器 SLIC Protection IC RoHS:否 制造商:STMicroelectronics 通道:8 Channels 擊穿電壓:8 V 電容:45 pF 端接類型:SMD/SMT 封裝 / 箱體:uQFN-16 功率耗散 Pd: 工作溫度范圍:- 40 C to + 85 C |
發布緊急采購，3分鐘左右您將得到回復。