- 您現在的位置：買賣IC網 > PDF目錄358770 > LC876662B (Sanyo Electric Co.,Ltd.) RF CONNECTOR; 50 OHM REVERSE POLARITY BNC MALE RIGHT ANGLE, CLAMP ATTACHMENT FOR RG59 & RG62; *MEETS FCC PART 15.203 REQUIREMENTS* PDF資料下載
參數資料
| 型號： | LC876662B |
| 廠商： | Sanyo Electric Co.,Ltd. |
| 英文描述： | RF CONNECTOR; 50 OHM REVERSE POLARITY BNC MALE RIGHT ANGLE, CLAMP ATTACHMENT FOR RG59 & RG62; *MEETS FCC PART 15.203 REQUIREMENTS* |
| 中文描述： | 8位單片機 |
| 文件頁數： | 9/23頁 |
| 文件大?。?/td> | 655K |
| 代理商： | LC876662B |
LC876694B/78B/62B
No.6843-9/23
Port Output Configuration
Output configuration and pull-up/pull-down resistor options are shown in the following table.
Input /output is possible even when port is set to output mode.
Terminal
Option applies to: Options
Output Format
Pull-up resistor
Pull-down
resistor
-
1
CMOS
Programmable
(Note 1)
None
P00 to P07
1 bit units
2
15 voltage Nch-open drain
-
1
CMOS
Programmable
-
P10 to P17
each bit
2
Nch-open drain
Programmable
-
1
CMOS
Programmable
-
P30 to P37
each bit
2
15V Nch-open drain
None
-
P70
-
None
Nch-open drain
Programmable
-
P71 to P73
-
None
CMOS
Programmable
-
P80 to P87
-
None
Nch-open drain
None
-
1
High voltage Pch-open drain
-
Fixed
S0/T0 to S6/T6
each bit
2
High voltage Pch-open drain
-
None
S7/T7 to S15/T15
S16 to S31
S32 to S47
-
None
High voltage Pch-open drain
-
fixed
1
High voltage Pch-open drain
-
Fixed
each bit
2
High voltage Pch-open drain
-
None
S48 to S51
-
None
High voltage Pch-open drain
-
None
XT1
-
None
Input only
None
-
XT2
-
None
Output for 32.768kHz crystal
oscillation
None
-
Note 1 Programmable pull-up resisters of Port 0 can be attatched in nibble units (P00-03, P04-07).
* Note 1: Connect as follows to reduce noise on VDD and increase the back-up time.
VSS1, and VSS2 must be connected together and grounded.
*Note 2 : The power supply for the internal memory is VDD1 but it uses the VDD2 as the power supply for ports. When the
VDD2 is not backed up, the port level does not become “H” even if the port latch is in the “H” level. Therefore,
when the VDD2 is not backed up and the port latch is “H” level, the port level is unstable in the HOLD mode, and
the back up time becomes shorter because the through current runs from VDD to GND in the input buffer.
If VDD2 is not backed up, output “L” by the program or pull the port to “L” by the external circuit in the HOLD
mode so that the port level becomes “L” level and unnecessary current consumption is prevented.
Back-up capacitors *2
Power
Supply
LSI
VDD1
VDD2
VDD3
VSS2
VSS1
VDD4
VFD
Powers
相關PDF資料 |
PDF描述 |
|---|---|
| LC8766C8A | 8-Bit Single Chip Microcontroller |
| LC876748A | 8-Bit Single Chip Microcontroller |
| LC876748C | CMOS LSI 8 BIT 1 CHIP MICROCOMPUTER |
| LC877248A | 8-Bit Single Chip Microcontroller with 48K-Byte(49151 ×8 bits) ROM and 2048-Byte(2048 ×8 bits) RAM On Chip(8位單片微控制器（帶片上48K（49151 ×8 bit）字節ROM和2048(2048 ×8 bits)字節RAM）) |
| LC8772C8B | 8-Bit Single Chip Microcontroller with 128KB Flash Momory and 2048-Byte RAM On Chip |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LC876670B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| LC876678B | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:8-Bit Single-Chip Microcontroller |
| LC876694B | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:8-Bit Single-Chip Microcontroller |
| LC876696A | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:8-Bit Single Chip Microcontroller |
| LC876696B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。