參數資料
型號: LC875016A
廠商: Sanyo Electric Co.,Ltd.
英文描述: 8-Bit Single Chip Microcontroller with 16K-Byte(16256 ×8 bits) EPROM and 640-Byte(640 ×9 bits) RAM On Chip(8位單片微控制器(帶片上16K(16256 ×8 bit)字節EPROM和640(640 ×9 bits)字節RAM))
中文描述: 8位微控制器的單芯片具有16K字節(16256 × 8位),EPROM和640字節(640 × 9位)片上的RAM(8位單片微控制器(帶片上16K的(16256 × 8位)字節存儲器和640(640 × 9位)字節的RAM))
文件頁數: 3/25頁
文件大小: 778K
代理商: LC875016A
LC875032A/24A/16A
3/25
(11) Remote control receiver circuit (connected to P73/INT3/T0IN terminal)
- Noise rejection function (noise rejection filter time constant can selected from 1/32/128 T
CYC
)
(12) Watchdog timer
- The watchdog timer period set by external RC.
- Watchdog timer can be set to produce interrupt, system reset
(13) Interrupts
- 16-source, 10-vectored interrupts:
1. Three level (low, high and highest) multiple interrupts are supported. During interrupt handling, an equal or
lower level interrupt request is refused.
2. If interrupt requests to two or more vector addresses occur at once, the higher level interrupt takes precedence.
In the case of equal priority levels, the vector with the lowest address takes precedence.
No.
Vector
Selectable Level
Interrupt signal
1
00003H
X or L
INT0
2
0000BH
X or L
INT1
3
00013H
H or L
INT2/T0L/INT4
4
0001BH
H or L
INT3/INT5/Base timer
5
00023H
H or L
T0H
6
0002BH
H or L
T1L/T1H
7
00033H
H or L
SIO0
8
0003BH
H or L
SIO1
9
00043H
H or L
ADC
10
0004BH
H or L
Port 0/PWM0, 1
Priority Level : X > H > L
For equal priority levels, vector with lowest address takes precedence.
(14) Subroutine stack levels
- 320 levels max. Stack is located in RAM
(15) Multiplication and division
- 16 bit × 8 bit
(executed in 5 cycles)
- 24 bit × 16 bit (12 cycles )
- 16 bit ÷ 8 bit
(8 cycles)
- 24 bit ÷ 16 bit (12 cycles)
(16) Oscillation circuits
- On-chip RC oscillation circuit used for system clock
- On-chip CF oscillation circuit used for system clock
- On-chip Crystal oscillation circuit used for system clock and time-base clock
(17) Standby function
- HALT mode
HALT mode is used to reduce power consumption. Program execution is stopped. Peripheral circuits still operate.
1. Oscillation circuits are not stopped automatically
2. Release on system reset
- HOLD mode
HOLD mode is used to reduce the power dissipation. Both program execution and peripheral circuits are stopped.
1. CF, RC and crystal oscillation circuits stop automatically
2. Release occurs on any of the following conditions
input to the reset pin goes low
a specified level is input to at least one of INT0, INT1, INT2, INT4, INT5
an interrupt condition arises at port 0
相關PDF資料
PDF描述
LC875064B 8-Bit Single Chip Microcontroller with 64K-Byte(65535 ×8 bits) EPROM and 2048-Byte(2048 ×8 bits) RAM On Chip(8位單片微控制器(帶片上64K(65535 ×8 bit)字節EPROM和2048(2048 ×8 bits)字節RAM))
LC875132A 8-Bit Single Chip Microcontroller with 32K-Byte(32512 ×8 bits) ROM and 1024-Byte(1024 ×8 bits) RAM On Chip(8位單片微控制器(帶片上32K(32512 ×8 bit)字節ROM和1024(1024 ×8 bits)字節RAM))
LC876564A 8-Bit Single Chip Microcontroller with 72/64 KB ROM and 2048-Byte RAM On Chip
LC876580B 8-Bit Single Chip Microcontroller with 96/80 KB ROM and 2048-Byte RAM On Chip
LC876662B RF CONNECTOR; 50 OHM REVERSE POLARITY BNC MALE RIGHT ANGLE, CLAMP ATTACHMENT FOR RG59 & RG62; *MEETS FCC PART 15.203 REQUIREMENTS*
相關代理商/技術參數
參數描述
LC875024A 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:8-Bit Single Chip Microcontroller with 32/24/16K-Byte EPROM and 640-Byte RAM On Chip
LC875032A 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:8-Bit Single Chip Microcontroller with 32/24/16K-Byte EPROM and 640-Byte RAM On Chip
LC875048B 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:8-Bit Single Chip Microcontroller with 64/56/48K-Byte EPROM and 2048-Byte RAM On Chip
LC875056B 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:8-Bit Single Chip Microcontroller with 64/56/48K-Byte EPROM and 2048-Byte RAM On Chip
LC875064B 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:8-Bit Single Chip Microcontroller with 64/56/48K-Byte EPROM and 2048-Byte RAM On Chip