- 您現在的位置：買賣IC網 > PDF目錄358769 > LC865504B (Sanyo Electric Co.,Ltd.) Octal Buffers/Drivers With 3-State Outputs 20-TSSOP -40 to 85 PDF資料下載
參數資料
| 型號： | LC865504B |
| 廠商： | Sanyo Electric Co.,Ltd. |
| 英文描述： | Octal Buffers/Drivers With 3-State Outputs 20-TSSOP -40 to 85 |
| 中文描述： | 8位單片機微控制器片20/16/12/08/04K-Byte ROM和512字節RAM |
| 文件頁數： | 4/19頁 |
| 文件大?。?/td> | 640K |
| 代理商： | LC865504B |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁
LC863532A/28A/24A/20A/16A
No.6844-4/19
(13) Interrupts
- 12 sources 8 vectored interrupts
1. External Interrupt INT0
2. External Interrupt INT1
3. External Interrupt INT2, Timer/counter T0L (Lower 8 bits)
4. External Interrupt INT3, base timer
5. Timer/counter T0H (Upper 8 bits)
6. Timer T1H, Timer T1L
7. Vertical synchronous signal interrupt (VS), horizontal line (
HS
)
8. IIC
- Interrupt priority control
Three interrupt priorities are supported (low, high and highest) and multi-level nesting is possible. Low or high
priority can be assigned to the interrupts from 3 to 8 listed above. For the external interrupt INT0 and INT1, low or
highest priority can be set.
(14) Sub-routine stack level
- A maximum of 128 levels (stack is built in the internal RAM)
(15) Multiplication/division instruction
- 16 bits
×
8 bits (7 instruction cycle times)
- 16 bits / 8 bits (7 instruction cycle times)
(16) 3 oscillation circuits
- Built-in RC oscillation circuit used for the system clock
- Built-in VCO circuit used for the system clock and OSD
- X’tal oscillation circuit used for base timer, system clock and PLL reference
(17) Standby function
- HALT mode
The HALT mode is used to reduce the power dissipation. In this operation mode, the program execution is
stopped. This mode can be released by the interrupt request or the system reset.
- HOLD mode
The HOLD mode is used to stop the oscillations; RC (internal), VCO, and X’tal oscillations. This mode can be
released by the following conditions.
Pull the reset terminal (RES) to low level.
Feed the selected level to either P70/INT0 or P71/INT1.
(18) Package
- MFP36S
- DIP36S
(19) Development tools
- Flash EEPROM:
LC86F3548A
- Evaluation chip:
LC863096
- Emulator:
EVA86000 (main) + ECB863400 (evaluation chip board)
+ POD36-CABLE (cable)
+ POD36-DIP (for DIP36S)
or POD36-MFP (for MFP36S)
相關PDF資料 |
PDF描述 |
|---|---|
| LC865516A | 8-Bit Single Chip Microcontroller with On-Chip 16K-Byte ROM and 512-Byte RAM(8位單片微控制器（帶片上16K字節ROM和512字節RAM）) |
| LC865608 | Octal Buffers/Drivers With 3-State Outputs 20-PDIP -40 to 85 |
| LC865612A | 8-Bit Single Chip Microcontroller |
| LC865624A | 8-Bit Single Chip Microcontroller with On-Chip 24K-Byte ROM and 640-Byte RAM(8位單片微控制器（帶片上24K字節ROM和640字節RAM）) |
| LC866008A | 8-bit single chip microcomputer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LC865508 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:8-Bit Single Chip Microcontroller with the One-Time Programmable PROM |
| LC865508B | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:8-Bit Single Chip Microcontroller with On-Chip 20/16/12/08/04K-Byte ROM and 512-Byte RAM |
| LC865512 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:8-Bit Single Chip Microcontroller |
| LC865512B | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:8-Bit Single Chip Microcontroller with On-Chip 20/16/12/08/04K-Byte ROM and 512-Byte RAM |
| LC865516 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:8-Bit Single Chip Microcontroller with the One-Time Programmable PROM |
發布緊急采購，3分鐘左右您將得到回復。