- 您現在的位置：買賣IC網 > PDF目錄358764 > LC75816E (Sanyo Electric Co.,Ltd.) 1/8 to 1/10 Duty Dot Matrix LCD Display Controllers/Drivers with Key Input Function PDF資料下載
參數資料
| 型號： | LC75816E |
| 廠商： | Sanyo Electric Co.,Ltd. |
| 英文描述： | 1/8 to 1/10 Duty Dot Matrix LCD Display Controllers/Drivers with Key Input Function |
| 中文描述： | 1月8日至1月10日當值點陣液晶顯示控制器/輸入功能的關鍵驅動 |
| 文件頁數： | 27/43頁 |
| 文件大?。?/td> | 572K |
| 代理商： | LC75816E |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁
No. 7142-27/43
LC75816E, 75816W
Voltage Detection Type Reset Circuit (VDET)
This circuit generates an output signal and resets the system when logic block power is first applied and when the voltage
drops, i.e., when the logic block power supply voltage is less than or equal to the power down detection voltage VDET,
which is 3.0V, typical. To assure that this function operates reliably, a capacitor must be added to the logic block power
supply line so that the logic block power supply voltage V
DD
rise time when the logic block power is first applied and the
logic block power supply voltage V
DD
fall time when the voltage drops are both at least 1 ms. (See Figure 3.)
Power Supply Sequence
The following sequences must be observed when power is turned on and off. (See Figure 3.)
Power on :Logic block power supply(V
DD
) on
→
LCD driver block power supply(V
LCD
) on
Power off:LCD driver block power supply(V
LCD
) off
→
Logic block power supply(V
DD
) off
However, if the logic and LCD driver blocks use a shared power supply, then the power supplies can be turned on and off
at the same time.
System Reset
1. Reset function
The LC75816E/W performs a system reset with the VDET. When a system reset is applied, the display is turned off, key
scanning is disabled, the key data is reset, and the general-purpose output ports are set to and held at the low level (V
SS
).
These states that are created as a result of the system reset can be cleared by executing the instruction described below.
(See Figure 3.)
Clearing the display off state
Display operation can be enabled by executing a “display on/off control” instruction. However, since the contents of the
DCRAM, ADRAM, and CGRAM are undefined, applications must set the contents of these memories before turning on
display with the “display on/off control” instruction. That is, applications must execute the following instructions.
Set display technique
DCRAM data write
ADRAM data write (If the ADRAM is used.)
CGRAM data write (If the CGRAM is used.)
Set AC address
Set display contrast (If the display contrast adjustment circuit is used.)
After executing the above instructions, applications must turn on the display with a “display on/off control” instruction.
Note that when applications turn off in the normal mode, applications must turn off the display with a “display on/off
control” instruction or the INH pin.
Clearing the key scan disable and key data reset states
Executing a "set key scan output port/general-purpose output port state" instruction not only creates a state in which
key scanning can be performed, but also clears the key data reset.
Clearing the general-purpose output ports locked at the low level (V
SS
) state
Executing a "set key scan output port/general-purpose output port state" instruction clears the general-purpose output
ports locked at the low level (V
SS
) state and sets the states of the general-purpose output ports.
相關PDF資料 |
PDF描述 |
|---|---|
| LC75817 | 1/8 to 1/10 Duty Dot Matrix LCD Display Controller/Driver with Key Input Function |
| LC75817NE | 1/8 to 1/10 Duty Dot Matrix LCD Display Controllers/Drivers with Key Input Function |
| LC75817NW | 1/8 to 1/10 Duty Dot Matrix LCD Display Controllers/Drivers with Key Input Function |
| LC75821E | LCD Display Drivers |
| LC75822E | LCD Display Drivers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LC75816W | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:1/8 to 1/10 Duty Dot Matrix LCD Display Controllers/Drivers with Key Input Function |
| LC75816W-8722-E | 制造商:ON Semiconductor 功能描述:LCD DISPLAY DRIVER - Trays 制造商:ON Semiconductor 功能描述:FTRAY / LCD DISPLAY DRIVER |
| LC75816WS-8722-E | 制造商:ON Semiconductor 功能描述:LCD DISPLAY DRIVER - Trays 制造商:ON Semiconductor 功能描述:FTRAY / LCD DISPLAY DRIVER |
| LC75817 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:1/8 to 1/10 Duty Dot Matrix LCD Display Controller/Driver with Key Input Function |
| LC75817E | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:1/8 to 1/10 Duty Dot Matrix LCD Display Controller/Driver with Key Input Function |
發布緊急采購，3分鐘左右您將得到回復。