- 您現在的位置：買賣IC網 > PDF目錄358764 > LC75808W (Sanyo Electric Co.,Ltd.) 1/8 to 1/10 Duty LCD Display Drivers with Key Input Function PDF資料下載
參數資料
| 型號： | LC75808W |
| 廠商： | Sanyo Electric Co.,Ltd. |
| 英文描述： | 1/8 to 1/10 Duty LCD Display Drivers with Key Input Function |
| 中文描述： | 1月8日至1月10日當值液晶顯示驅動器與關鍵輸入功能 |
| 文件頁數： | 24/39頁 |
| 文件大小： | 981K |
| 代理商： | LC75808W |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁
No. 6370 -24/39
LC75808E, 75808W
3. In sleep mode
The pins KS1 to KS6 are set to high or low by the KC1 to KC6 bits in the control data.
If a key on one of the lines corresponding to a KS1 to KS6 pin which is set high is pressed, the oscillator on the
OSC pin is started and a key scan is performed. Keys are scanned until all keys are released. Multiple key presses
are recognized by determining whether multiple key data bits are set.
If a key is pressed for longer than 800T(s)(where T= ——
low level on DO) to the controller. The controller acknowledges this request and reads the key data. However, if
CE is high during a serial data transfer, DO will be set high.
After the controller reads the key data, the key data read request is cleared (DO is set high) and the LC75808E/W
performs another key scan. However, this dose not clear sleep mode. Also note that DO, being an open-drain
output, requires a pull-up resistor (between 1 k
and 10 k
).
Sleep mode key scan example
Example: When the control data bits KC1 to KC5 are 0, KC6 is 1, and SP is 1. (sleep with only KS6 high)
Multiple Key Presses
Although the LC75808E/W is capable of key scanning without inserting diodes for dual key presses, triple key presses on
the KI1 to KI5 input pin lines, or multiple key presses on the KS1 to KS6 output pin lines, multiple presses other than
these cases may result in keys that were not pressed recognized as having been pressed. Therefore, a diode must be
inserted in series with each key. Applications that do not recognize multiple key presses of three or more keys should
check the key data for three or more 1 bits and ignore such data.
fosc
Note:
*
4.These diodes are required to reliable recognize multiple key presses on the KS6 line when sleep mode state with only KS6 high, as in the above
example. That is, these diodes prevent incorrect operations due to sneak currents in the KS6 key scan output signal when keys on the KS1 to KS5
lines are pressed at the same time.
[ L ]
[ L ]
[ L ]
[ L ]
[ L ]
[ H ]
相關PDF資料 |
PDF描述 |
|---|---|
| LC75808E | 1/8 to 1/10 Duty LCD Display Drivers with Key Input Function |
| LC75811E | 1/8 to 1/10 Duty Dot Matrix LCD Display Controller/Driver |
| LC75814V | 1/4 Duty General-Purpose LCD Driver |
| LC75816E | 1/8 to 1/10 Duty Dot Matrix LCD Display Controllers/Drivers with Key Input Function |
| LC75817 | 1/8 to 1/10 Duty Dot Matrix LCD Display Controller/Driver with Key Input Function |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LC75808W-E | 功能描述:LCD 驅動器 LCD DISPLAY DRIVER RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube |
| LC75808WS-E | 功能描述:LCD 驅動器 RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube |
| LC75808W-SH-E | 功能描述:LCD 驅動器 RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube |
| LC75809PT-H | 制造商:ON Semiconductor 功能描述:LCD DISPLAY DRIVER - Trays |
| LC75809PTH-H | 制造商:ON Semiconductor 功能描述:LCD DISPLAY DRIVER - Trays |
發布緊急采購，3分鐘左右您將得到回復。