參數資料
型號: LC72705E
廠商: Sanyo Electric Co.,Ltd.
英文描述: FM Multiplex Receiver IC for VICS Systems(用于VICS系統的FM多路接收器芯片)
中文描述: 多重調頻接收機集成電路VICS系統(用于VICS系統的調頻多路接收器芯片)
文件頁數: 7/14頁
文件大?。?/td> 165K
代理商: LC72705E
Frame synchronization error protection count
This IC detects the four unique BIC inflection points that exist in a single frame, and increments or decrements the
protection counter depending on whether or not the IC internal frame synchronization counter matches. The data values
are set in the same way as those for the block synchronization protection count are set, namely data in which 1 has been
subtracted from the desired protection count must be transferred. The frame synchronization default values are 8 for
forward protection and 2 for backward protection.
Control registers
These registers are used to set the IC operating mode. These are described later.
Notes
— The address bits DI12 to DI15 are ignored.
— Addresses other than those listed above (for example location 0110) are special addresses used for test mode and
other special IC functions. Do not set these locations.
— The default values are the values reloaded into the internal registers when a reset signal (RST) is received. These
values are the recommended values for normal operation, and normally do not need to be modified. If only the
default values are used, there is no need to provide data transfer routines in the external CPU or microcontroller.
Layer 4 CRC Check Circuit
This is a function provided for data group error detection, i.e. layer 4 CRC. After the stipulated number of bytes of data
group data and a 16-bit CRC error check word are transferred, the CRC4 pin outputs a high level if there were no errors.
The CRC4 pin outputs a high level if all the bits in the IC internal CRC check register were 0. When using this function
to perform the layer 4 CRC check, the IC internal CRC check register must be initialized before a single data group data
unit is transferred. This register is initialized by sending bit 7 of the control register. Note that since this flag is not
automatically reset to 0, the application must return it to 0 before transferring layer 4 CRC check data. If there were no
errors in any of the received data groups, the CRC register will always be all zeros after the CRC check of a single data
group. Therefore, the above control register initialization will not be necessary as long as there are no errors in the layer 4
CRC. The data length of the transferred data group data is in units of 8 bits. Also note that while there is no upper limit
on the amount of data transferred in a single operation, data transfers may also be divided into multiple transfer
operations.
No. 5744-7/14
LC72705E
Note:
*
Both forward and backward protection counts are 3.
Figure 1 Block Synchronization Protection Operation (forward
backward
forward)
Received data
Synchronization
counter BIC position
Reset
相關PDF資料
PDF描述
LC72705 FM Multiplex Receiver IC for VICS Systems
LC72706E FM Multiplex Receiver IC Supporting All Worldwide Standards(適用于全球統一標準的FM多路接收器芯片)
LC72707 FM Multiplex Receiver IC Supporting All Worldwide Standards
LC72707E RESTR 121 1 TOL 1/8W
LC72708E FM Multiplex Broadcast Reception IC for Mobile VICS Systems(用于移動VICS系統的FM多路廣播接收芯片)
相關代理商/技術參數
參數描述
LC72706 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:FM Multiplex Receiver IC Supporting All Worldwide Standards
LC72706E 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:FM Multiplex Receiver IC Supporting All Worldwide Standards
LC72707 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:FM Multiplex Receiver IC Supporting All Worldwide Standards
LC72707E 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:FM Multiplex Receiver IC Supporting All Worldwide Standards
LC72708 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:FM Multiplex Broadcast Reception IC for Mobile VICS Systems