- 您現在的位置：買賣IC網 > PDF目錄358759 > LC7218M (Sanyo Electric Co.,Ltd.) PLL Frequency Synthesizer for Electronic Tuning in AV Systems PDF資料下載
參數資料
| 型號： | LC7218M |
| 廠商： | Sanyo Electric Co.,Ltd. |
| 英文描述： | PLL Frequency Synthesizer for Electronic Tuning in AV Systems |
| 中文描述： | 鎖相環頻率合成器的AV系統的電子調諧 |
| 文件頁數： | 13/16頁 |
| 文件大小： | 265K |
| 代理商： | LC7218M |
Next, the value of the general-purpose counter after the measurement completes must be read out while CTEN is still 1.
(The general-purpose counter is reset when CTEN is set to 0.)
Another point that requires care here is that before starting the general-purpose counter, it must be reset by setting
CTEN to 0.
Note that although signals input to the LCTR pin are transmitted directly to the general-purpose counter, signals input to
the HCTR pin are divided by eight internally before being transmitted to the general-purpose counter. Therefore the
value of the general-purpose counter will be 1/8 of the actual frequency input to the HCTR pin.
When counting intermediate frequency signals, always have the controller first check for the presence of the IF-IC SD
(station detect) signal and then only turn on the IF counter buffer output if the SD signal was present. Auto-search
techniques that only use an IF count are subject to stopping at frequencies where there is no station due to leakage output
from the IF counter buffer.
Note that although the DO pin is forced to the high level when the general-purpose counter is started (when CTEN is set
to 1), the DO pin automatically goes low when the measurement completes (after either 60 or 120 ms has elapsed or
when a signal has been applied for one or two periods). Therefore the DO pin can be used to check for measurement
completion.
1. When the general-purpose is not used (when CTEN is 0) the DO pin can be used to check for changes in external
signals.
When mode 3 is specified and data is output through DO, DO will automatically go high after data output has
completed, i.e., when CE goes low.
After that, DO goes low automatically when the IN0 signal changes state.
(That is, DO can be used to check for changes in an external signal input to IN0.)
No. 4758-13/16
LC7218, 7218M, 7218JM
相關PDF資料 |
PDF描述 |
|---|---|
| LC72191JM | PLL Frequency Synthesizer for Electronic Tuning in Car Stereo Tuners |
| LC72191 | PLL Frequency Synthesizer for Electronic Tuning in Car Stereo Tuners |
| LC72191M | PLL Frequency Synthesizer for Electronic Tuning in Car Stereo Tuners |
| LC7219 | PLL Frequency Synthesizers |
| LC7219M | PLL Frequency Synthesizers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LC7218M-TLM-E | 制造商:Sony Semiconductor Solutions Division 功能描述: |
| LC7219 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:PLL Frequency Synthesizers |
| LC72191 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:PLL Frequency Synthesizer for Electronic Tuning in Car Stereo Tuners |
| LC72191JM | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:PLL Frequency Synthesizer for Electronic Tuning in Car Stereo Tuners |
| LC72191JMA-AH | 功能描述:時鐘合成器/抖動清除器 RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。