- 您現在的位置：買賣IC網 > PDF目錄358748 > LB1872 (Sanyo Electric Co.,Ltd.) Polygon Mirror Scanner Driver IC(多邊形鏡像掃描儀驅動器) PDF資料下載
參數資料
| 型號： | LB1872 |
| 廠商： | Sanyo Electric Co.,Ltd. |
| 英文描述： | Polygon Mirror Scanner Driver IC(多邊形鏡像掃描儀驅動器) |
| 中文描述： | 多邊形鏡掃描儀驅動IC（多邊形鏡像掃描儀驅動器） |
| 文件頁數： | 6/11頁 |
| 文件大小： | 166K |
| 代理商： | LB1872 |
Pin No.
Symbol
Pin function
Equivalent circuit
No. 5625-6/11
LB1872
Pin Functions
1
2
3
4
5
6
IN3
–
IN3
+
IN1
–
IN1
+
IN2
–
IN2
+
Hall amplifier inputs
IN
+
> IN
–
is the input high state, and the reverse is the input low state.
Connect a capacitor between the IN
+
and IN
–
inputs if there is noise in
the Hall sensor signals.
An amplitude of over 50 mV p-p and under 350 mV p-p is desirable in
the Hall sensor signals. Kickback may occur in the output if the input
signal has an amplitude greater than 350 mV p-p.
7
8
9
OUT3
OUT2
OUT1
Motor drive outputs
Connect capacitors between the motor outputs (or between the motor
outputs and ground) if oscillation occurs in the outputs. (Use capacitors
in the range 0.1 μF to 0.47 μF.)
10
RF
Output current detection
Connect a resistor (Rf) between this pin and ground.
The output current is limited to be up to I
OUT
= V
REG
/Rf.
11
V
CC
Power supply
12
V
REG
Stabilized power supply output (5-V output)
Connect a capacitor (about 0.1 μF) between this pin and ground for
stabilization.
13
14
XO
XI
Crystal oscillator connections
These pins are used to drive the reference clock oscillator element.
If an external clock (with a frequency of a few MHz) is used, connect a
resistor (about 13 k
) to the XI pin in series and input the clock signal
through that resistor. Leave the XO pin open in this case.
Continued on next page.
相關PDF資料 |
PDF描述 |
|---|---|
| LB1875 | Polygon Mirror Motor Predriver IC |
| LB1876 | Three-Phase Brushless Motor Driver for Polygon Mirror Motors |
| LB1877 | Brushless Motor Driver with Speed Control for Portable Cassette Recorders |
| LB1877M | Brushless Motor Driver with Speed Control for Portable Cassette Recorders |
| LB1877V | Brushless Motor Driver with Speed Control for Portable Cassette Recorders |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LB1875 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Polygon Mirror Motor Predriver IC |
| LB1876 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Three-Phase Brushless Motor Driver for Polygon Mirror Motors |
| LB1876(36SOP) | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Controller Miscellaneous - Datasheet Reference |
| LB1876_09 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:For Polygon Mirror Motors 3-phase Brushless Motor Driver |
| LB1876-MPB-E | 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。