- 您現在的位置：買賣IC網 > PDF目錄358747 > LB1862 (Sanyo Electric Co.,Ltd.) Fan Motor Single-Phase Full-Wave Driver PDF資料下載
參數資料
| 型號： | LB1862 |
| 廠商： | Sanyo Electric Co.,Ltd. |
| 英文描述： | Fan Motor Single-Phase Full-Wave Driver |
| 中文描述： | 風扇電機單相全波驅動 |
| 文件頁數： | 6/7頁 |
| 文件大小： | 41K |
| 代理商： | LB1862 |
LB1862
No. 6208-6/7
Design reference
(1) V
CC
pin
Power supply pin for control block and motor drive.
Accepts a wide operation voltage range from 3.8 to 16.8V, for 5V/12V dual power supply support.
(2) OUT1, OUT2 pins
Single-phase coil output pins.
Bipolar drive output with upper side inverted and lower side single output. Built-in regenerative circuit regenerates
kickback current between lower side NPN outputs when a diode is used for protection against IC destruction caused
by reverse connection.
(3) IN
–
, IN
+
pins
Hall input signal pins
The Hall signal is amplified into a square wave by the Hall amplifier with hysteresis characteristics of
±
3.5 mV
(typ.). The Hall input signal amplitude should be 70 mV or more.
(4) CT pin
This pin serves for connecting a capacitor between CT and GND.
The capacitor determines the characteristics of the built-in lockup protection circuit for preventing coil burnout in
the case of motor restraint. Once normal motor load is restored, the automatic recovery circuit resets itself.
Changing the capacitance alters the lockup detection time.
When a 0.47
μ
F capacitor is connected between CT and GND
Lockup detection time
Lockup protection time/automatic recovery time
: approx. 0.5s
: approx. 0.16s (output ON)
approx. 1s (output OFF)
When not using lockup protection function, this pin should be connected to ground.
(5) RD pin
Open-collector output pin that is Low during rotation and OFF when lockup is detected.
The output is a latch type which stays OFF also when the automatic recovery circuit has restored drive mode, unless
the rotation actually resumes.
(6) ST pin and HB pin
ST pin : When input to this pin is High, motor drive is stopped (OUT is high impedance).
At this time, RD output indicates lockup protection mode OFF.
HB pin : Hall bias switching pin. At ST pin High input, Hall bias is cut off to reduce current drain in fan standby
mode.
If not used, both pins should be open.
(7) Thermal protection circuit
When internal temperature Tj of IC reaches 180
°
C, output current limiter is activated to protect against damage.
相關PDF資料 |
PDF描述 |
|---|---|
| LB1863M | Two-Phase Unipolar Brushless Motor Driver Automatic Recovery Type Circuit in a Miniature Flat Package |
| LB1868M | RES 10.0MEGOHM MTL FLM.40W 1% TR |
| LB1868 | Two-Phase Brushless Fan Motor Driver |
| LB1870 | Three-Phase Brushless Motor Driver(3相位無電刷馬達驅動器) |
| LB1871 | Three-Phase Brushless Motor Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LB1862_09 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:For Fan Motor Single-Phase Full-Wave Driver |
| LB1862-E | 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LB1862M | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Fan Motor Single-Phase Full-Wave Drivers |
| LB1862M_09 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:For Fan Motor Single-Phase Full-Wave Driver |
| LB1862MC | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Monolithic Digital IC For Fan Motor Single-Phase Full-Wave Driver |
發布緊急采購，3分鐘左右您將得到回復。